Huawei NE40E-X1 Hardware Description Download Page 6

Page: 6 / 158

2.1.6 Number of Main Parts and Slot Layout of the NE40E-X2......................................................................25

2.2 Power Supply System.......................................................................................................................................26

2.2.1 Architecture of the Power Supply System...............................................................................................26
2.2.2 Diagram of the Power Supply Architecture............................................................................................26
2.2.3 DC Power Supply System.......................................................................................................................27

2.3 Heat Dissipation System...................................................................................................................................29

2.3.1 Air Channel..............................................................................................................................................29
2.3.2 Fan Module..............................................................................................................................................29

2.4 Data Plane.........................................................................................................................................................32

2.4.1 Introduction to the Data Plane.................................................................................................................32
2.4.2 Introduction to the NPUI-20....................................................................................................................33

2.5 Control Plane....................................................................................................................................................35

2.5.1 Introduction to the Control Plane............................................................................................................35
2.5.2 MPUG......................................................................................................................................................36

2.6 Physical Specifications.....................................................................................................................................40

2.6.1 Chassis Specifications.............................................................................................................................40
2.6.2 Board Specifications................................................................................................................................41

3 Boards............................................................................................................................................42

4 Cables.............................................................................................................................................73

4.1 DC Power Cables..............................................................................................................................................74
4.2 Chassis and Cabinet Grounding Cable.............................................................................................................75

4.2.1 Introduction.............................................................................................................................................75
4.2.2 Structure...................................................................................................................................................75
4.2.3 Technical Specifications..........................................................................................................................75

4.3 Console Port Cable...........................................................................................................................................76

4.3.1 Introduction.............................................................................................................................................76
4.3.2 Structure...................................................................................................................................................76
4.3.3 Technical Specifications..........................................................................................................................77

4.4 Auxiliary Port Cable.........................................................................................................................................77

4.4.1 Introduction.............................................................................................................................................78
4.4.2 Structure...................................................................................................................................................78
4.4.3 Technical Specifications..........................................................................................................................79

4.5 Clock Cable......................................................................................................................................................79

4.5.1 Introduction.............................................................................................................................................79

HUAWEI NE40E-X1 & NE40E-X2 Universal Service
Router
Hardware Description

Contents

Issue 02 (2011-09-10)

Huawei Proprietary and Confidential

Summary of Contents for NE40E-X1































































































































































Search results

Summary of Contents for NE40E-X1

Reviews:

Huawei NE40E-X1, Hardware Description, Page: 6 / 158

Search results

Summary of Contents for NE40E-X1

Reviews: