Huawei IPC6122-P Configuration Manual Download Page 49

Page: 49 / 115

Figure 6-7

Privacy Mask Parameters tab page

Step 2

To enable the privacy mask function, select

Enable

Step 3

Click

Add privacy

Add mosaics

A privacy mask area is displayed on the video image.

NOTE

You can add only one privacy mask area at a time. After the add operation is complete, save data for the
settings to take effect.

The privacy mask areas on live video images are displayed in black or mosaics effect. You can add a
maximum of eight black areas and a maximum of two mosaics areas.

Step 4

Use the mouse to adjust the location and size of the privacy mask area.

Step 5

Click

Save

Step 6

Go to the

Preview

page and check whether the location and size of the privacy mask area

meet the requirements.

If yes, the configuration is complete.

If no, configure the privacy mask area again.

NOTE

You can delete unnecessary privacy mask areas. In the

No.

area, select the ID of the privacy mask area to

delete, and click

Delete

----End

6.6 Setting Motion Detection Parameters

An alarm is generated when an object moves within the specified surveillance range of the
camera.

Procedure

Step 1

Choose

Settings

Channel Configuration

Motion Detection Parameters

The page for setting motion detection parameters is displayed, as shown in

Figure 6-8

IPC6122-P
Configuration Guide

6 Setting Video Parameters

Issue 02 (2016-04-06)

Huawei Proprietary and Confidential

Summary of Contents for IPC6122-P




















































































































Search results

Summary of Contents for IPC6122-P

Reviews:

Related manuals for IPC6122-P

Brands by name

Popular brands

Huawei IPC6122-P, Configuration Manual

Search results

Summary of Contents for IPC6122-P

Reviews:

Related manuals for IPC6122-P

Brands by name

Popular brands