Huawei IPC6122-P Configuration Manual Download Page 50

Page: 50 / 115

Figure 6-8

Motion detection Parameters tab page

Step 2

To enable motion detection, select

Enable

Step 3

Click

Add

A motion detection area is displayed on the live video image.

NOTE

You can add only one motion detection area at a time. If you need to add more motion detection areas,
click

Add

again.

A maximum of four motion detection areas can be added.

Step 4

Use the mouse to adjust the location and size of the motion detection area.

Step 5

Set parameters. For detailed parameter description, see

Table 6-5

Parameter description

Parameter

Description

Alarm check interval

Time interval at which the system checks for new alarms. The
system then reports detected alarms to the surveillance platform.

NOTE

The MTU value is an integer ranging from 1 to 256. The default
value of is

Only one alarm is reported if an object keeps moving in the
surveillance range of the camera within a single alarm check interval.
This is to avoid repeated alarms.

Sensitivity

Indicates the sensitivity of motion detection.

NOTE

The MTU value is an integer ranging from 1 to 5. The default value
of is

A larger value indicates higher sensitivity. To detect slight motion, it
is recommended that you set the sensitivity to a larger value.

Step 6

Click

Save

IPC6122-P
Configuration Guide

6 Setting Video Parameters

Issue 02 (2016-04-06)

Huawei Proprietary and Confidential

Summary of Contents for IPC6122-P




















































































































Search results

Summary of Contents for IPC6122-P

Reviews:

Related manuals for IPC6122-P

Brands by name

Popular brands

Huawei IPC6122-P, Configuration Manual

Search results

Summary of Contents for IPC6122-P

Reviews:

Related manuals for IPC6122-P

Brands by name

Popular brands