Huawei IPC6122-P Configuration Manual Download Page 37

Page: 37 / 115

Figure 6-1

Video&Audio Stream Parameters page

Step 2

Set video stream parameters. For detailed parameter description, see

Table 6-2

Parameter description

Parameter

Description

Stream type

Set the stream type based on the site requirements. The options
are as follows:

Primary stream

: The primary stream is large in size and

provides clear video while occupying large bandwidth, so it is
used in local storage.

Secondary stream

: The secondary stream provides smooth

video, occupies small bandwidth, and is used for data
transmission on low-bandwidth networks.

NOTE

The IPC currently supports dual-stream output only.

Mirroring mode

When the mirroring mode is enabled, you can reverse video
images. The options are as follows:

Close

: The mirroring mode is disabled.

Horizontal reversion

: Video images can be reversed left to

right.

Vertical reversion

: Video images can be reversed upside

down.

All

: Video images can be reversed upside down and left to

right.

Corridor mode

When the corridor mode is enabled, you can reverse video
images by 90 degrees to obtain the aspect ratio 9:16 or 3:4.

IPC6122-P
Configuration Guide

6 Setting Video Parameters

Issue 02 (2016-04-06)

Huawei Proprietary and Confidential

Summary of Contents for IPC6122-P




















































































































Search results

Summary of Contents for IPC6122-P

Reviews:

Related manuals for IPC6122-P

Brands by name

Popular brands

Huawei IPC6122-P, Configuration Manual

Search results

Summary of Contents for IPC6122-P

Reviews:

Related manuals for IPC6122-P

Brands by name

Popular brands