Huawei IPC6122-P Configuration Manual Download Page 46

Page: 46 / 115

Parameter

Description

White balance mode

White balance adjusts the color circuit within a camera to
remove color cast and ensure accurate color reproduction in
various lighting conditions. The options are as follows:

Auto

: The camera automatically adjusts the red and blue

offsets in environments where the color temperature
ranges from 3000 K to 7500 K. Video images may slant
blue in the morning or at dusk.

Manual

: The red and blue offsets must be adjusted

manually.

Indoor

: The camera automatically adjusts the red and

blue offsets in indoor environments where the color
temperature ranges from 4500 K to 5500 K and tungsten
lamps or incandescent lamps are used.

Outdoor

: This mode applies to sunny outdoor

environments where the color temperature ranges from
5500 K to 6500 K.

Fixed sodium lamp

: This mode applies to environments

where the color temperature ranges from 2000 K to 2300
K and sodium lamps are turned on.

NOTE

When

White balance mode

is set to

Auto

, you can drag the

sliders or enter values in the spin boxes to adjust the blue and
red fine-tune offset values. These values are integers ranging
from 0 to 255.

When

White balance mode

is set to

Manual

, you can drag the

sliders or enter values in the spin boxes to adjust the blue and
red intense-tune offset values. These values are integers ranging
from 0 to 255.

It is recommended that you use the

Auto

mode.

Noise reduction switch

Noise reduction level

is available only when you set

Noise

reduction switch

Enable

Increasing the noise reduction level improves the noise
reduction effect but decreases the image clarity.

Brightness

Indicates an attribute of visual perception in which a source
appears to be radiating or reflecting light.

Hue

Indicates the degree to which a stimulus can be described as
similar to or different from stimuli that are described as red,
green, blue, and yellow.

Saturation

Indicates the colorfulness of a color relative to its own
brightness.

Contrast

Contrast is the ratio of black and white colors in an image.

Increasing the contrast improves the image clarity and
color brightness.

Decreasing the contrast dims the entire image.

IPC6122-P
Configuration Guide

6 Setting Video Parameters

Issue 02 (2016-04-06)

Huawei Proprietary and Confidential

Summary of Contents for IPC6122-P




















































































































Search results

Summary of Contents for IPC6122-P

Reviews:

Related manuals for IPC6122-P

Brands by name

Popular brands

Huawei IPC6122-P, Configuration Manual

Search results

Summary of Contents for IPC6122-P

Reviews:

Related manuals for IPC6122-P

Brands by name

Popular brands