background image

420010970304 - LP-700 Rev. 000 Rel. 002 Date 4.21.21

16

WARNING

!

Do not attempt to vent this appliance by any means other than 

those described in this manual. Doing so will void the warranty and 

may result in severe personal injury or death.

Approved Carbon Monoxide Detectors: Each carbon monoxide 

detector as required in accordance with the above provisions shall 

comply with NFPA 70 and be ANSI/UL 2034 listed and IAS certified.

I. Prevent Combustion Air Contamination

Install intake air piping for the boiler as described in the Venting 

Section, this manual. Do not terminate exhaust in locations that can 

allow contamination of intake air.

WARNING

!

Ensure that the intake air will not contain any of the contaminants 

in Table 7. Contaminated air will damage the boiler, resulting in 

possible substantial property damage, severe personal injury, or 

death. For example, do not pipe intake air near a swimming pool or 

laundry facilities. These areas always contain contaminants.

of qualified licensed professionals for the installation of hard wired 

carbon monoxide detectors.

a. In the event that the vented gas fueled appliance is installed in a 

crawl space or attic, the hard wired carbon monoxide detector with 

alarm and battery back-up shall be installed on the next adjacent 

floor level.

b. In the event that these requirements cannot be met at the time 

of completion of installation, the owner shall have a period of 

thirty (30) days to comply with the above requirements; provided, 

however, that during said thirty (30) day period, a battery operated 

carbon monoxide detector with an alarm shall be installed.

Figure 9 - CO Warning Label

J. Removing a Boiler from a Common Vent System

WARNING

!

Failure to follow all instructions can result in flue gas spillage and 

carbon monoxide emissions, causing severe personal injury or 

death.

DANGER

!

Do not install the boiler into a common vent with any other 

appliance. This will cause flue gas spillage or appliance malfunction, 

resulting in possible substantial property damage, severe personal 

injury, or death.

When removing an existing boiler, follow the steps below.

1. Seal any unused openings in the common venting system.

2. Visually inspect the venting system for proper size and horizontal 

pitch to determine if there is blockage, leakage, corrosion, or other 

deficiencies that could cause an unsafe condition.

3. If practical, close all building doors, windows, and doors between 

the space in which the boiler remains connected to the common 

venting system and other spaces in the building. Turn on clothes 

dryers and any appliances not connected to the common venting 

system. Turn on any exhaust fans, such as range hoods and bathroom 

exhausts, at maximum speed. Do not operate a summer exhaust fan. 

Close all fireplace dampers.

4. Place in operation the appliance being inspected. Follow the 

lighting instructions. Adjust the thermostat so the appliance will 

operate continuously.

5. Test for spillage at the draft hood relief opening after 5 minutes of 

main burner operation. Use the flame of a match or candle or smoke 

from a cigarette.

6. After it has been determined that each appliance remaining 

connected to the common venting system properly vents when 

tested as outlined, return doors, windows, exhaust fans, fireplace 

dampers, and any other gas burning appliances to their previous 

condition of use.

7. Any improper operation of the common venting system should 

be corrected to conform to the National Fuel Gas Code, ANSI Z223.1. 

When resizing any portion of the common venting system, the 

system should approach the minimum size as determined using the 

appropriate tables in Appendix G of ANSI Z223.1.

NOTE: DAMAGE TO THE BOILER CAUSED BY EXPOSURE TO 

CORROSIVE VAPORS IS NOT COVERED BY WARRANTY. (Refer to 

the limited warranty for complete terms and conditions.)

Products to Avoid

Areas Likely to Have 

Contaminants

Spray cans containing 

fluorocarbons

Dry cleaning / laundry areas 

and establishments

Permanent wave solutions

Swimming pools

Chlorinated waxes / cleaners

Metal fabrication plants

Chlorine-based swimming pool 

chemicals

Beauty shops

Calcium chloride used for 

thawing

Refrigeration repair shops

Sodium chloride used for water 

softening

Photo processing plants

Refrigerant leaks

Auto body shops

Paint or varnish removers

Plastic manufacturing plants

Hydrochloric or Muriatic acid

Furniture refinishing areas and 

establishments

Cements and glues

New building construction

Antistatic fabric softeners used 

in clothes dryers

Remodeling areas

Chlorine-type bleaches, laundry 

detergents, and cleaning 

solvents

Garages and workshops

Adhesives used to fasten 

building products

Table 7 - Products and Areas Likely to Have Contaminants

Summary of Contents for ELU Series





































































































Reviews: