manualshive.com logo in svg

HP StorageWorks 7100 - Virtual Array, Appendix, Page: 5 / 27

Share
Download
HP StorageWorks 7100 - Virtual Array Appendix Download Page 5

Event 

Number 

(dec/hex) 

Event 
Name 

Logged? 

Predictive 

Maintenance 

Implication 

Suspected 
Components 

Mf

g Fail? 

Description 

51/0x33 

Offline firmware download 
with disk size derating 

N 

Ignore 

None 

N 

An offline controller firmware download was 
attempted while disk size derating was in effect.  
Derating of the disks causes the shutdown portion of 
the offline download to post the shutdown image at 
the wrong location on the disk, and, as a result, the 
subsystem boots to a No Maps state after the 
download.  To prevent this error, remove the disk 
derating and try the download again. 

52/0x34 

Concurrent downloads 
attempted 

Y 

Ignore - Host 

Problem 

None 

Y 

A host attempted to start a controller firmware 
download operation while another was already in 
progress. 

53/0x35 

Feature capability exceeded 

N 

Ignore - Host 

Porblem 

None 

N 

A host request was found to require more capability 
than current feature licensing has enabled.  This may 
be a request for an operation that is not enabled in a 
currently licensed feature. 

54/0x36 

Incompatible Image family 

N 

Ignore - Normal 

for some cases of 

firmware 

None 

N 

The firmware image that was sent is of a family that 
is incompatible with the currently executing 
firmware.  As a result, the download cannot be 
performed online. 

55/0x37 

Configuration change occurred 
during discover subsystem 

N 

Ignore - should 

be handled by 

host 

None 

Y 

A configuration change or component hot plug was 
detected during the execution of the Discover 
Subsystem command.  As a result, the response that 
was built may not reflect the current configuration. 

56/0x38 

Download Image Checksum 
Failure 

Y 

Ignore - Likely 

image 

distribution 

problem 

None 

Y 

The firmware image that was sent contained defects 
such that the checksum verification failed. 

57/0x39 

Unavailable Data Detected By 
RAID1 Read 

Y 

Ignore - See 

accompanying 

errors 

None 

N 

R1 detected that the devices necessary for a read 
were not available for access before the access was 
attempted.  This can apply to an initial attempt to 
read or to a retry. 

58/0x3a 

Unavailable Data Detected By 
RAID1 Write 

Y 

Ignore - See 

accompanying 

errors 

None 

N 

R1 detected that the devices necessary for a write 
were not available for access before the access was 
attempted.  This can apply to an initial attempt to 
write or to a retry. 

59/0x3b 

Disk Interface Error 

Y 

N.A. 

None 

Y 

An error occurred on a disk interface command. 

60/0x3c 

Unsupported feature 

N 

Ignore. Device 

Management 

error 

None 

Y 

An attempt was made to install a license for a 
feature that this product does not support. 

61/0x3d 

LUN specified exceeds 
maximum 

N 

N.A. 

None 

Y 

An 8-byte hierarchic LUN reference specified a 
LUN value that exceeds the maximum specified by 
the LUN creation limit mode parameter. 

62/0x3e 

Reassign Failed 

Y 

Single 

Occurrance 

Disk Drive 

Y 

The PDD’s attempts to reassign a bad block failed 
due to device errors. 

63/0x3f 

Reassign Out Of Resources 

Y 

Single 

Occurrance 

Disk Drive 

Y 

The PDD was unable to complete a Reassign Blocks 
command because the sparing buffer is too small. 

64/0x40 

Optimal Space Error In RAID 
5 

Y 

Ingore 

None 

N 

R5 detected that space allocated for an "optimal 
only" migrating write (i.e. rebuild policy) was no 
longer optimal after the write had completed.  The 
write completed in degraded mode but the client 
module requires an optimal completion as indicated 
by the optimal only allocation hint. 

65/0x41 

Optimal Space Error In RAID 
1 

Y 

Ignore 

None 

N 

R1 detected that space allocated for an "optimal 
only" migrating write (i.e. rebuild policy) was no 
longer optimal after the write had completed.  The 
write completed in degraded mode but the client 
module requires an optimal completion as indicated 
by the optimal only allocation hint. 

66/0x42 

No Shutdown Image Posted 

N 

N.A. 

None 

Y 

CFM could not shutdown subsystem because no 
volume set members was successfully posted with 
the NVRAM image. 

67/0x43 

Bad Disk Drive State During 
Add Physical Drive 

N 

N.A. 

None 

N 

A drive was in the initialization failed state after the 
spin up attempt during an add physical drive 
command.  The drive is failing initialization, so 
information on the nature of the failure should 
appear in the log. 

68/0x44 

Disk Interface Data Underrun 

Y 

N.A. 

None 

N 

A backend device sent/received less data than 
expected. 

69/0x45 

Disk Interface Data Overrun 

Y 

N.A. 

None 

N 

A backend device sent/received more data than 
expected. 

Summary of Contents for StorageWorks 7100 - Virtual Array




























Reviews:

No comments