manualshive.com logo in svg

HP StorageWorks 7100 - Virtual Array, Appendix, Page: 21 / 27

Share
Download
HP StorageWorks 7100 - Virtual Array Appendix Download Page 21

Event 

Number 

(dec/hex) 

Event 
Name 

Logged? 

Predictive 

Maintenance 

Implication 

Suspected 
Components 

Mf

g Fail? 

Description 

download mode 

battery charger 

download mode to update the charger firmware 

436/0x1b4 

TWSI bus is busy 

Y 

Ignore, unless 

occurring 

frequently 

Controller 

N 

The two-wire serial bus local to the controlle is 
busy. 

437/0x1b5 

NVRAM battery not present 

Y 

 

NVRAM 
battery 

N 

The NVRAM battery charger does not detect the 
presence of NVRAM battery 

438/0x1b6 

NVRAM battery failed 

Y 

 

NVRAM 
battery 

Y 

The NVRAM battery charger has declared the 
NVRAM battery as failed 

439/0x1b7 

NVRAM battery not 
responding 

Y  NVRAM 

battery 

Y 

The NVRAM battery is not responding to two-wire 
serial bus commands 

440/0x1b8 

NVRAM battery 
reconditioning stopped 

Y  NVRAM 

battery charger 

N 

The NVRAM battery charger has aborted the 
reconditioning of a battery 

441/0x1b9 

NVRAM battery 
reconditioning started 

Y  NVRAM 

battery charger 

N 

The NVRAM battery charger has successfully 
started reconditioning of a battery. 

442/0x1ba 

Array switched to secure mode 

Y 

 

NVRAM 
battery 

N 

The array has been switched to secure mode due to 
the condition of the batteries 

443/0x1bb 

Array out of secure mode 

Y 

 

NVRAM 
battery 

N 

The array has been switched out of secure mode 
since the condition of the batteries do not warrant it 
anymore 

444/0x1bc 

Turning on LED due to battery 
failure 

Y  Battery 

amber 

LED 

Y 

The amber LED that indicates battery failure has 
been turned on due to a battery failure condition.  
When this log entry is unaccompanied by the log 
entry, it indicates that the battery management 
firmware module was unable to communicate with 
the NVRAM battery.  Possible two-wire serial bus 
communication error. 

445/0x1bd 

Battery has reached end of life 

Y 

 

NVRAM 
battery 

Y 

The NVRAM battery internal status indicates that 
the battery has reached the end of life condition 

446/0x1be 

NVRAM battery status is 
LOW 

Y  NVRAM 

battery 

N 

The status of NVRAM battery is low. This means 
that the battery charge is less than a specified 
threshold value 

447/0x1bf 

NVRAM battery status is 
GOOD 

Y  NVRAM 

battery 

N 

The status of NVRAM battery is good. This means 
that the battery charge is equal or higher than a 
specified threshold value 

448/0x1c0 

NVRAM battery status is 
UNKNOWN 

Y  NVRAM 

battery 

N 

The status of the NVRAM battery is unknown. This 
may be due to the firmware not being able to 
communicate with the battery 

449/0x1c1 

TWSI bus has been requested 
by another module 

Y Ignore, 

unless 

occurring 

frequently 

Controller, 
battery, power 
supply 

N 

The battery management firmware has received a 
request from another firmware module to use the 
two-wire serial bus 

450/0x1c2 

Unable to communicate with 
the NVRAM battery charger 

Y  Controller, 

battery 

Y 

The battery management firmware module is unable 
to communicate with the NVRAM battery charger. 
Possible two-wire serial bus communication error 

451/0x1c3 

NVRAM battery 
reconditioning done 

Y  NVRAM 

battery charger 

N 

The NVRAM battery charger has successfully 
reconditioned a battery 

452/0x1c4 

NVRAM battery 
reconditioning status 

Y  NVRAM 

battery 

N 

The state of the controller and batteries that are 
checked before a decision is taken on reconditioning 

453/0x1c5 

EEPROM status is good 

Y 

 

 

N 

The eeprom can be communicated with and has 
valid contents. 

454/0x1c6 

EEPROM status is "not 
present" 

Y 

 

 

N 

Communication with the eeprom has failed.  The 
module assumes that no hardware is present. 

455/0x1c7 

EEPROM status is "failed" 

Y 

 

 

Y 

The TWSI bus may have failed, the read after a 
write resulted in inconsistent data, or the crc 
checksums in a device and it’s mirror (if available) 
are not correct. 

456/0x1c8 

EEPROM status is "unknown" 

Y 

 

 

N 

This can is caused when an TWSI bus command 
fails.  The eeprom is marked as unknown until a 
retry is done or the TWSI bus reports a hard failure. 

457/0x1c9 

Invalid state in state machine 

Y 

 

 

Y 

This is caused by an invalid state in an eeprom state 
machine.  If this error is found, there is a bug in the 
firmware which must be fixed. 

458/0x1ca 

TWSI Request Failure 

Y 

 

Controller, 
battery, power 
supply, 
midplane 

Y 

The two-wire serial bus module would not allow the 
read or write request.  This is usually due to a bus 
failure. 

459/0x1cb 

TWSI Read Failure 

Y 

 

Controller, 
battery, power 
supply, 
midplane 

Y 

The two-wire serial bus module retried the read and 
was either not able to get a response from the 
device, the transaction failed, or the bus failed.  In 
the case of a bus failure, the bus was good at the 
time the read request was made.  Now it has failed. 

Summary of Contents for StorageWorks 7100 - Virtual Array




























Reviews:

No comments