manualshive.com logo in svg

HP StorageWorks 7100 - Virtual Array, Appendix, Page: 12 / 27

Share
Download
HP StorageWorks 7100 - Virtual Array Appendix Download Page 12

FC-SCSI Interface SpecificationDescribes the IceCube SCSI interface. Targetted as part of OEM manual.Disk Array Con
 

Error! No text of specified style in document. 

Event 

Number 

(dec/hex) 

Event 
Name 

Logged? 

Predictive 

Maintenance 

Implication 

Suspected 
Components 

Mf

g Fail? 

Description 

in the queue have been processed, the subsystem 
will undergo a short reset at which time the 
correctable error will be permanently corrected. 

286/0x11e 

Memory Compare Error 

Y 

Ingore - See 

accompanying 

errors 

SDRAM, 
controller, 
midplane 

Y 

This error code indicates that the system 
experienced a compare error between the redundant 
shared memory copies.  The two word queue entry 
found in the shared-memory controller error queue 
will be placed in the event extended info area. After 
all entries currently in the queue have been 
processed, the subsystem will undergo a short reset, 
at which time an attempt will be made to sync the 
two copies of memory (if available) to see if the 
error was transient. If the error is permanent, non-
volatile memory must be invalidated.  Single 
miscompare can be recovered by selecting one of 
the two versions of the data and syncing both sides 
to that version. 

287/0x11f 

Controller Data Bus 
Microprocessor Access Parity 
Error 

Y 

> 1 in 6 months 

Controller 

N 

This event code indicates that the a reset was 
initiated due to excessive errors on the 
microprocessor local bus. 

288/0x120 

Internal Data Bus Error 

Y 

> 1 in 6 months 

Controller, 
SIMM 

N 

This error code indicates that the system 
experienced a parity error during a DMA Operation. 

289/0x121 

Volume Set Full Reset 

Y 

Ignore - see 

accompanying 

errors 

None 

N 

This error code indicates that an inconsistancy was 
detected in one of the volume set clusters seed 
values, fsb or rbtables.  The migration bypassed this 
cluster.  This could be the result of a r6 restore 
consistency posting temporary data to the cluster, 
the data in the cluster will remain bad until the data 
is reposted by the cache.  In the mean time all reads 
for data will be satisfied by the cache.  After the 
cache repost the data may then be successfully 
migrated. 

290/0x122 

Warm Boot IO Expander Fault 

Y 

Ignore if 

recovered by 

power cycle 

Controller 

Y 

This error code indicates that the IO Expander 
containing the warm boot bit did not power-on in 
the correct default condition or that attempts to set 
the warm boot bit in the IO Expander failed. 

291/0x123 

Disk Set Detached 

Y 

Ignore - 

Operator/Host 

activity 

None 

N 

This is a system change event posted to the log 
when shutdown has completed sucessfully; i.e., the 
volume set is no longer attacheddevice number field 
in log record is volume set number (system change 
event) 

292/0x124 

Microprocessor Software Fault 

Y 

> 1 in 1 month 

Controller 

N 

This is an error detected by the processor which 
caused the processor to vector to the software fault 
isr. The controller always resets following this log 
entry.  This error is caused by illegal instruction 
fetches, divide by zero, or other illegal processor 
activity. 

293/0x125 

Microprocessor Hardware 
Fault 

Y 

> 1 in 1 month 

Controller 

N 

This is an error detected by the processor which 
caused the processor to vector to the hardware fault 
isr. The controller always resets following this log 
entry.  This error occurs when the microprocessor 
attempts an illegal interrupt vector. 

294/0x126 

Disk Interface Event 

Y 

Ignore, unless 

occurring 

frequently 

Disk, 
controller, disk 
interface 

N 

An error occurred on the disk interface.  These may 
occur during disk hotplug.  More detailed status is 
available in the event expanded information. 

295/0x127 

Insufficient RAM For Image 
Upload 

Y 

Ignore - Operator 

error or 

accompanying 

errors 

None 

N 

This is an error detected by the startupSystem when 
the current RAM config is not large enough to hold 
the NV image stored on disk.  Since we do not 
support shrinking RAM, this fails the upload 
process and causes a new VS to be created.  System 
state is NO_MAPS. 

296/0x128 

Disk Interface Queueing 
Disabled 

Y Immediate 

Performance 

Problem - 

Unsupported 

Disk 

Disk 

N 

An attached disk could not be configured for 
command queueing.  Command queueing and 
disconnects are disabled for this interface. 

297/0x129 

Disk Disconnects Disabled 

Y 

Immediate 

Performance 

Disk 

N 

This event indicates that the firmware could not 
configure the drive to disable disconnects during 

Summary of Contents for StorageWorks 7100 - Virtual Array




























Reviews:

No comments