manualshive.com logo in svg

HP StorageWorks 7100 - Virtual Array, Appendix, Page: 24 / 27

Share
Download
HP StorageWorks 7100 - Virtual Array Appendix Download Page 24

FC-SCSI Interface SpecificationDescribes the IceCube SCSI interface. Targetted as part of OEM manual.Disk Array Con
 

Error! No text of specified style in document. 

Event 

Number 

(dec/hex) 

Event 
Name 

Logged? 

Predictive 

Maintenance 

Implication 

Suspected 
Components 

Mf

g Fail? 

Description 

revision that is unsupported by this firmware. 

502/0x1f6 

Enclosure NV memory 
contains an invalid mode 
parameter 

Y 

 

controller 

N 

During an upload of enclosure-specific mode 
parameters from enclosure NV memory, an invalid 
value was found.  A default value for this parameter 
is being substituted. 

503/0x1f7 

Enclosure Power Switch 
Pressed 

Y 

 

enclosure 

N 

The enclosure power switch has been pressed. 

504/0x1f8 

Event Log uploaded 

Y 

 

controller 

N 

The event log data prior to this entry has been 
uploaded from an image copy (due to invalid 
NVRAM).  There has been an unknown amount of 
elapsed time after uploaded log entries that is not 
accounted for in the current system time.  Following 
this entry and prior to the LOG_UPLOAD_DONE 
entry are any events logged prior to the upload.  
Times for those events will not be consistent with 
any other log entries, but will be internally 
consistent. 

505/0x1f9 

Event Log upload complete 

Y 

 

controller 

N 

The event log data prior to this entry and following 
the entry have occurred prior to the upload of the 
event log image.  These entries have been recorded 
with a system time that is not consistent with the 
uploaded entries, or the time in this entry and those 
following it. 

506/0x1fa 

Power Supply EEPROM Failed 

Y 

 

Power Supply 

Y 

Unable to communicate with the power supply 
EEPROM.  It is assumed to be failed.  The power 
supply must be replaced. 

507/0x1fb 

Temperature Sensor Failed 

Y 

 

Controller 

Y 

A write/read to/from the Temperature sensor failed. 

508/0x1fc 

format subsystem reset 

Y 

 

controller 

N 

This event code indicates that the controller reset 
due to a format subsystem command. 

509/0x1fd 

Miscompare during midplane 
EEPROM selftest 

Y 

 

midplane 

Y 

This event code indicates that the data on the two 
eeproms at a given location was different.  This 
problem is usually fixed if the firmware can write to 
the eeproms. 

510/0x1fe 

FC Signal Detect Interrupt 

Y 

 

VSC7130 PBC 
/ Dual Repeater 
Chip 

N 

An interrupt on one of the VSC7130 port-bypass 
control / signal detect chips has occurred.  See the 
extended information for details. 

511/0x1ff 

Dual-controller clock sync 
error 

Y 

 

controller 

N 

An interrupt from the shared-memory controller 
reported the controller clocks were more than 1 tick 
out of sync with each other. 

512/0x200 

Event Log copy from 
NVSRAM start 

Y 

 

controller 

N 

Following this entry, events are being added to the 
log from NVSRAM entries that were written when 
the log memory was not available.  The time and 
sequence numbers for these entries may not be 
valid.  Some normal entries may be interleaved with 
these entries.  The completion of the additions will 
be noted by a corresponding event log system event. 

513/0x201 

Event Log copy from 
NVSRAM complete 

Y 

 

controller 

N 

The addition of entries from NVSRAM to the 
controller log has been completed.  The time and 
sequence numbers for those entries may not be 
valid.  Some normal entries may be interleaved with 
those entries.  The start of the additions should have 
been noted by a corresponding event log system 
event. 

514/0x202 

Power supply failure 

Y 

 

Power Supply 

Y 

Indicates the output voltages supplied by the power 
supply have dropped below or raised above their 
normal operating ranges. This can be ignored if seen 
after a sudden power loss, or when unplugging, 
plugging in, removing, or inserting power supplies. 

515/0x203 

Cannot communicate with the 
power supply expander 

Y 

 

Power Supply 

Y 

The communication with the power supply expander 
was not successful  

516/0x204 

The power supply eeprom had 
an error 

Y 

 

Power Supply 

Y 

The EEPROM update function returned an error 

517/0x205 

The power supply blower had 
an error 

Y 

 

Power Supply 

Y 

The Blower update function returned an error 

518/0x206 

The over voltage error bit is set 

Y 

 

Power Supply 

Y 

The over voltage error bit is set in the power supply 
expander  

519/0x207 

The over current error bit is set 

Y 

 

Power Supply 

Y 

The over current error bit is set in the power supply 
expander  

Summary of Contents for StorageWorks 7100 - Virtual Array




























Reviews:

No comments