HP ProCurve 6108 Management And Configuration Manual Download Page 274 | Manualshive

Page: 274 / 547

background image

Port-Based Virtual LANs (VLANs) and GVRP

Port-Based Virtual LANs (Static VLANs)

VLAN Tagging Information

VLAN tagging enables traffic from more than one VLAN to use the same port.
(Even when two or more VLANs use the same port they remain as separate
domains and cannot receive traffic from each other without going through an
external router.) As mentioned earlier, a “tag” is simply a unique VLAN
identification number (VLAN ID, or VID) assigned to a VLAN at the time that
you configure the VLAN name in the switch. The tag can be any number from
1 to 4094 that is not already assigned to a VLAN. When you subsequently assign
a port to a given VLAN, you must implement the VLAN tag (VID) if the port
will carry traffic for more than one VLAN. Otherwise, the port VLAN assign
ment can remain “untagged” because the tag is not needed. On a given switch,
this means you should use the “Untagged” designation for a port VLAN
assignment where the port is connected to non 802.1Q-compliant device or is
assigned to only one VLAN. Use the “Tagged” designation when the port is
assigned to more than one VLAN or the port is connected to a device that

does

comply with the 802.1Q standard.

For example, if port A7 on an 802.1Q-compliant switch is assigned to only the
Red VLAN, the assignment can remain “untagged” because the port will
forward traffic only for the Red VLAN. However, if both the Red and Green
VLANs are assigned to port A7, then at least one of those VLAN assignments
must be “tagged” so that Red VLAN traffic can be distinguished from Green
VLAN traffic. The following illustration shows this concept:

Blue

Server

White

Server

Green

Server

Red

Server

Red

VLAN

Blue

VLAN

White
VLAN

Green
VLAN

Green
VLAN

Red

VLAN

Switch

"X"

5

6

7

4

1

3

2

Switch

"Y"

5

4

1

3

2

Red

VLAN:

Untagged

Green

VLAN:

Tagged

Ports 1-6: Untagged
Port 7: Red VLAN Untagged

Green VLAN Tagged

Ports 1-4: Untagged
Port 5: Red VLAN Untagged

Green VLAN Tagged

Figure 12-16. Example of Tagged and Untagged VLAN Port Assignments

12-22

«
...
272
273
274
275
276
...
»

Summary of Contents for ProCurve 6108




































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 6108

Brand: Parker Pages: 344

Brand: IBM Pages: 248

Brand: F5 Pages: 2

Brand: F5 Pages: 90

Brand: F5 Pages: 47

Brand: National Instruments Pages: 34

MultiConnect SE MTS2EA

Brand: Multitech Pages: 8

Brand: ZyXEL Communications Pages: 125

Brand: Patton electronics Pages: 12

NI WLS/ENET-9163

Brand: National Instruments Pages: 36

Anybus Communicator ABC4021

Brand: HMS Networks Pages: 60

Brand: 4G Systems Pages: 2

Brand: PairGain Pages: 80

Brand: RTS Pages: 3

Brand: TP-Link Pages: 113

Brand: VIA Technologies Pages: 25

Brand: Helmholz Pages: 14

Brand: Belkin Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands