manualshive.com logo in svg

HP Netserver LP 2000r, Service Manual, Page: 77 / 98

Share
Download
HP Netserver LP 2000r Service Manual Download Page 77

Chapter 6

Replacing Parts

71

4. Slide the Netserver back into the rack.

Removing the Air Flow Guide

The air flow guide directs air onto the processor heatsinks. The air flow guide sits directly over the DIMMs
and must be removed to install or remove DIMMS.

1. Remove the top cover as previously described.

2. Unplug the air flow guide fan cable from the system board.

3. Lift up the air flow guide to remove it.

Removing the Air Flow Guide

Replacing the Air Flow Guide

To replace the air flow guide, simply reverse the steps described in the preceding procedure.

Removing Hot Swap Hard Drives

 

CAUTION

Remove the drive slowly. Wait for the drive heads to park before completely
removing the drive. Follow the instructions carefully to prevent damage to the drive
head and head actuator.

1. To unlock the drive, insert your thumb into the opening at the center of the drive and pull the

ejector arms outward until they click into the open position.

Summary of Contents for Netserver LP 2000r



































































































Reviews:

No comments