manualshive.com logo in svg

HP Netserver LP 2000r, Service Manual, Page: 4 / 98

Share
Download
HP Netserver LP 2000r Service Manual Download Page 4

Contents

iv

Video Connector ......................................................................................................................................16

LAN Connector.........................................................................................................................................17

SCSI .........................................................................................................................................................18

3 Parts Information........................................................................................................................................19

Exploded View – External ............................................................................................................................19

Exploded View – Internal..............................................................................................................................20

Replaceable Parts List .................................................................................................................................21

Parts List Identifier........................................................................................................................................21

4 Diagnostics .................................................................................................................................................23

Diagnostic Tests...........................................................................................................................................23

Diagnostics Description............................................................................................................................23

HP Netserver DiagTools...............................................................................................................................23

DiagTools Capabilities .............................................................................................................................24

Introduction...................................................................................................................................................25

Tools Required.........................................................................................................................................26

Common Installation Problems ....................................................................................................................26

Troubleshooting Sequence ......................................................................................................................26

Netserver Will Not Power On ...................................................................................................................26

Problems after Netserver is Powered On ................................................................................................27

Error Messages ............................................................................................................................................28

POST Error Messages .............................................................................................................................29

Power On Self Test (POST) Error Codes ................................................................................................30

Beep Codes .............................................................................................................................................40

Clearing the CMOS Configuration ...........................................................................................................41

Resetting a Lost Password ......................................................................................................................42

Hardware Problems......................................................................................................................................42

Monitor Does Not Work............................................................................................................................43

Keyboard or Mouse Does Not Work ........................................................................................................43

CD-ROM Drive Does Not Work ...............................................................................................................43

SCSI Device Does Not Work ...................................................................................................................44

Replacing a Battery ......................................................................................................................................44

Problems Running the Setup Utility..............................................................................................................45

5 Troubleshooting .........................................................................................................................................47

Summary of Contents for Netserver LP 2000r



































































































Reviews:

No comments