manualshive.com logo in svg

HP Netserver LP 2000r, Service Manual, Page: 24 / 98

Share
Download
HP Netserver LP 2000r Service Manual Download Page 24

Chapter 2

System Information

18

SCSI

There is one external SCSI connector on the back of the server.

34

68

1

35

Wide SCSI Connector Pinout

Pin

Signal

Pin

Signal

1

S1 (+DB 12)

35

S35 (-DB 12)

2

S2 (-DB 13)

36

S36 (-DB 13)

3

S3 (+DB 14)

37

S37 (-DB 14)

4

S4 (+DB 15)

38

S38 (-DB 15)

5

S5 (+DB P1)

39

S39 (-DB P1)

6

S6 (+DB 0)

40

S40 (-DB 0)

7

S7 (+DB 1)

41

S41 (-DB 1)

8

S8 (+DB 2)

42

S42 (-DB 2)

9

S9 (DB 3)

43

S43 (-DB 3)

10

S10 (+DB 4)

44

S44 (-DB 4)

11

S11 (+DB5)

45

S45 (-DB 5)

12

S12 (+DB 6)

46

S46 (-DB 6)

13

S13 (+DB 7)

47

S47 (-DB 7)

14

S14 (+DB P)

48

S48 (-DB P)

15

S15

49

S49

16

S16 (DIFFSENS)

50

S50

17

S17 (TERMPWR)

51

S51 (TERMPWR)

18

S18 (TERMPWR)

52

S52 (TERMPWR)

19

S19 (RESERVED)

53

S53 (RESERVED)

20

S20

54

S54

21

S21 (+ATN)

55

S55 (-ATN)

22

S22 S22

56

S56

23

S23 (+BSY)

57

S57 (-BSY)

24

S24 (+ACK)

58

S58 (-ACK)

25

S25 (+RST)

59

S59 (-RST)

26

S26 (+MSG)

60

S60 (-MSG)

27

S27 (+SEL)

61

S61 (-SEL)

28

S28 (+C/D)

62

S62 (-C/D)

29

S29 (+REQ)

63

S63(-REQ)

30

S30 (+I/O)

64

S64 (-I/O)

31

S31 (+DB 8)

65

S65 (-DB 8)

32

S32 (+DB 9)

66

S66(-DB 9)

33

S33 (DB 10)

67

S67 (-DB 10)

34

S34 (DB 11)

68

S68 (-DB 11)

Summary of Contents for Netserver LP 2000r



































































































Reviews:

No comments