manualshive.com logo in svg

HP Netserver LP 2000r, Service Manual, Page: 75 / 98

Share
Download
HP Netserver LP 2000r Service Manual Download Page 75

Chapter 6

Replacing Parts

69

Removing the Front Bezel

The front bezel protects the power and reset switches from being accidentally disabled. You need to remove
the front bezel in order to install mass storage devices or media. You do not need to turn off power to remove
the front bezel.

1. Grasp the bezel at the opening in the center, and pull towards you to release the top edge of the

bezel.

2. Pull and lift the bezel out toward you to remove it from the chassis.

Pin

Pin

A

B

 Removing the Front Bezel

NOTE

The front bezel pivots on two pins at the bottom and is held in place with spring
latches at the top.

Replacing the Front Bezel

1. Place the bottom edge of the bezel into the hinge pins at the bottom front of the chassis.

2. Pivot the bezel to close it and press the top corners to snap it into place.

Removing the Top Cover

You do not need to remove the front bezel to remove the top cover of the Netserver. However, the front
bezel must be removed to install mass storage devices or media.

1. If the HP Netserver is operating, log off all users and shutdown the operating system.

2. Pull out the anti-tip foot at the bottom of the rack. Then slowly slide the HP Netserver chassis

out from the rack.

3. Disconnect the power cord(s) and unplug telephone cables.

4. Release the top cover by turning the knob at the front of the chassis in a clockwise direction.

5. Slide the top cover about 1½ inches toward the front of the Netserver and then lift it off the

chassis.

Summary of Contents for Netserver LP 2000r



































































































Reviews:

No comments