HP iPAQ h4100 User Manual Download Page 69

Page: 69 / 76

Troubleshooting

User’s Guide

6-1

Troubleshooting

Problem

Solution

I cannot get a GPS signal

Ensure your GPS receiver is switched on and fully charged up.

Take your GPS receiver outside so you have a clear view of the

sky.

Allow 5-10 minutes to receive a GPS signal. If GPS receiver has a
valid signal, the green LED flashes.

I cannot connect my GPS

receiver to my PocketPC

Check your GPS receiver and your iPAQ PocketPC are within 5-
10 yards apart.

Check the Bluetooth Radio on your iPAQ PocketPC is switched on
by tapping the Bluetooth icon at the bottom right side of the Start
screen.

Check your GPS receiver is switched on and charged.

Switch on the power switch; if the GPS receiver is not charged up
the power LED is red.

Switch on Navigation system. The GPS receiver should automati-
cally connect with the iPAQ PocketPC. If this does not happen,
follow the instructions in the User’s Guide to connect the GPS
receiver with the iPAQ PocketPC.

I cannot install the maps

Ensure your iPAQ PocketPC is connected via Microsoft Active-

sync with your Desktop.

Ensure Navigation System is installed on the iPAQ PocketPC.

(There should be an icon in the

Start> Programs

menu).

Perform a soft reset on your iPAQ PocketPC before trying to

install any maps. (Refer to your iPAQ PocketPC User’s Guide for
details. All data and settings are retained).

Ensure Navigation System is closed. From the

Start

menu select

Settings > System

Memory >Running Programs

iPAQ Nav

System

Stop.

Verify there is sufficient memory in your selected target location.

Verify the correct CD-Rom is inserted in your CD drive

My GPS receiver has asked me

for a passkey to connect

The GPS receiver has a default passkey of 2003.

The Bluetooth Manager may be set to require a passkey.

Tap on the

Bluetooth

icon >

Bluetooth Settings

Tap the right arrow key at the bottom of the screen to the

Serial

Port

tab.

Ensure the

Authentication (Passkey) required

check box is

unchecked.

I cannot find a location

Check the address is entered correctly.

Check the appropriate map for the address is loaded.

Sometimes an address is not stored in the database. Navigation

Technologies is always updating the map content. To provide feed-
back and add a new address complete a Feedback Form on
www.hp.com/go/ipaqnavigation

Summary of Contents for iPAQ h4100













































































Search results

Summary of Contents for iPAQ h4100

Reviews:

Related manuals for iPAQ h4100

Brands by name

Popular brands

HP iPAQ h4100, User Manual

Search results

Summary of Contents for iPAQ h4100

Reviews:

Related manuals for iPAQ h4100

Brands by name

Popular brands