manualshive.com logo in svg

HP E4418B, Programming Manual

The HP E4418B User Manual is a comprehensive guide that provides detailed instructions and essential information for the efficient operation of the product. It is available for free download from our website, allowing users to easily access and benefit from this valuable resource.

Share
Download
background image

prog.book : chapter1.fm    25  Mon Feb 15 09:24:37 1999

Power Meter Remote Operation

Making Measurements

HP E4418B/E4419B Programming Guide

1-25

Example 4 - Specifying the Resolution Parameter

The previous examples detailed the use of the expected value and source
list parameters. The resolution parameter is used to set the resolution of
the specified window. This parameter does not affect the resolution of the
HP-IB data, however it does affect the auto averaging setting (refer to
Figure 1-3 on page 1-49).

Since the filter length used for a channel with auto-averaging enabled is
dependent on the window resolution setting, a conflict arises when a given
channel is set up in both windows and the resolution settings are
different. In this case, the higher resolution setting is used to determine
the filter length.

The following example uses the resolution parameter to specify a
resolution setting of 3. This setting represents 3 significant digits if the
measurement suffix is W or %, and 0.01 dB if the suffix is dB or dBm (for
further details on the resolution parameter refer to the commands in
Chapter 2, “MEASurement Instructions”). Also, in this example the
expected power and source list parameters are defaulted. The expected
power value will be left unchanged at its current setting. The source list
parameter will be defaulted as described in the note on page 1-18. Note
that as the source list parameter is the last specified parameter you do not
have to specify

DEF

.

Using

READ?

Some fine tuning of the above program segment can be carried out for
example, by setting the trigger delay off. The following program segment
assumes that channel A is currently being measured on the upper window.

ABOR1

CONF1 DEF,3

TRIG1:DEL:AUTO OFF

READ1?

Using

INITiate and FETCh?

ABOR1

Aborts channel A.

CONF1 DEF,3

Configures the upper window to make a
measurement using the current setting of the
expected power and source list and a resolution
setting of 3.

READ1?

Takes the upper window’s measurement. This will be
a channel A or B measurement depending on current
window setup

Summary of Contents for E4418B


































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for E4418B

PAT DS 150 Service Manual preview
DS 150
Brand: PAT Pages: 55
PAT DS 150 User Manual preview
DS 150
Brand: PAT Pages: 31
Valor 203 Installation Manual preview
203
Brand: Valor Pages: 13
Campbell 108 Instruction Manual preview
108
Brand: Campbell Pages: 31
Datalogic Smart-VS Quick Reference Manual preview
Smart-VS
Brand: Datalogic Pages: 6
Datakom DKM-411 Quick Start Manual preview
DKM-411
Brand: Datakom Pages: 4
Datakom DKM-407 User Manual preview
DKM-407
Brand: Datakom Pages: 38
Facom 701A Instruction Manual preview
701A
Brand: Facom Pages: 42
OHAUS MC2000 Instruction Manual preview
MC2000
Brand: OHAUS Pages: 84
Tascam SX-1 Application Manual preview
SX-1
Brand: Tascam Pages: 4
Harpers NL-404 Service Manual preview
NL-404
Brand: Harpers Pages: 8
OHAUS MB90 User Manual preview
MB90
Brand: OHAUS Pages: 52
PCB Piezotronics 393B32 Installation And Operating Manual preview
393B32
Brand: PCB Piezotronics Pages: 15
Stübbe DFM 350 Original Operating Manual preview
DFM 350
Brand: Stübbe Pages: 12
Emos P5821 Manual preview
P5821
Brand: Emos Pages: 76
Hanna Instruments HI 93414 Instruction Manual preview
HI 93414
Brand: Hanna Instruments Pages: 52
Badger Meter Recordall Series User Manual preview
Recordall Series
Brand: Badger Meter Pages: 8
SKF TKST 11 Instructions For Use Manual preview
TKST 11
Brand: SKF Pages: 12

Brands by name

Popular brands

Load more brands