manualshive.com logo in svg

HP 64700 series, User Manual

Share
Download
HP 64700 series User Manual Download Page 77

Initialize with user-defined files (activity or duration
measurement).

Initialize with global symbols (activity measurement).

Initialize with local symbols (activity measurement).

R estore a previous performance measurement (if the
emulation system has been exited and reentered).

Default Initialization

Entering the "performance_measurement_initialize" command
with no options specifies an activity measurement.  If a valid
symbolic database has been loaded, the addresses of all global
procedures and static symbols will be used; otherwise, a default set
of ranges that cover the entire processor address range will be used.

Initialization with User Defined Ranges

You can specifically give the SPMT address or time ranges to use
by placing the information in a file and entering the file name in
the "performance_measurement_initialize" command.  The formats
for the address range file (activity measurements) and time range
file (duration measurements) are described below.

Address Range File Format.

Address range files may contain

program symbols (procedure name or static), user defined address
ranges, and comments.  An example address range file is shown
below.

# Any line which starts with a # is a comment. 
# All user’s labels must be preceded by a "|". 
 
|users_label  10H 1000H 
program_symbol 
 
# A program symbol can be a procedure name or a static.  In the case of a pro- 
# cedure name the range of that procedure will be used. 

|users_label2 program_symbol1 -> program_symbol2 
 
# "->" means thru.  The above will define a range which starts with symbol1 
# and goes thru symbol2.  If both symbols are procedures then the range will 
# be defined as the start of symbol1 thru the end of symbol2. 

dir1/dir2/source_file.s:local_symbol 

Performance Measurements  4-7

Summary of Contents for 64700 series

























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands