manualshive.com logo in svg

HP 64700 series, User Manual

Share
Download
HP 64700 series User Manual Download Page 100

The measurements for each label are printed in descending order
according to the amount of activity.  You can see that the
"math_library" function has the most activity.  Also, you can see
that no activity is recorded for several of the functions.  The
histogram portion of the report compares the activity in the
functions that account for at least 1%  of the activity for all labels
defined in the measurement.

Duration

Measurement

Examples

Before you perform duration measurements, you should be aware
of the prefetch and recursion considerations associated with these
measurements.

Prefetch and Recursion Considerations

When using the SPMT to perform duration measurements, there
should be only two addresses stored in the trace memory: the entry
address, and the exit address.  Prefetches or recursion can place
several entry addresses before the first exit address, and/or several
exit addresses before the first entry address.  Duration
measurements are made between the last entry address in a series
of entry addresses, and the last exit address in a series of exit
addresses (see figure 4-4).  All of the entry and exit addresses which
precede these last addresses are assumed to be unused prefetches,
and are ignored during time measurements.

                    START  - unused prefetch 
                    START  - unused prefetch 
                    START  - unused prefetch 
                    START  - START actually taken -
                    END    - unused prefetch 
                    END    - unused prefetch             Measure duration
                    END    - unused prefetch 
                    END    - END actually taken   -
                    START  - unused prefetch 
                    START  - unused prefetch             Measure duration
                    START  - unused prefetch 
                    START  - START actually taken -
                    END    - unused prefetch 
                    END    - unused prefetch 

Figure 4-4.  Prefetch Correction

4-30  Performance Measurements

Summary of Contents for 64700 series

























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands