![background image](http://html.mh-extra.com/html/hp/635n-jetdirect-ipv6-ipsec-print-server/635n-jetdirect-ipv6-ipsec-print-server_administrators-manual_163681101.webp)
IP Address
Mask
Description
192.1.0.0
255.1.0.0
Allow all hosts on network 192, subnet 1.
192.168.1.2
Allow the host with IP address 192.168.1.2. The mask
255.255.255.255 is assumed and is not required.
To add an entry into the access control list, use the
IP Address
and
Mask
fields to specify a host, and
click (check) the
Save
checkbox for that entry. Then click
Apply
.
To delete an entry from the list, clear the
Save
checkbox for that entry. Then click
Apply
.
To clear the entire access control list, clear all
Save
checkboxes, and click
Apply
.
Mgmt. Protocols
This link provides access to management communications and other protocols that affect security.
Web Mgmt.
Use this tab to manage communications with the embedded Web server from Web browsers.
Secure, encrypted Web-based communication is provided through the Secure HTTP (HTTPS) protocol.
If configured to require HTTPS, the embedded Web server routes HTTPS communications through port
443, the well-known port for HTTPS traffic. Although ports 80, 280, or 631 continue for Internet Printing
Protocol (IPP) use, other non-secure communications (HTTP) are redirected to HTTPS. Redirection of
your browser to use HTTPS may be transparent depending on your browser's capabilities.
NOTE:
IPP is not supported on value-based print servers.
By factory default, HP Jetdirect print servers and printers with IPsec support are configured to require
HTTPS only.
Although not recommended, HTTPS and HTTP communications that are not secure can be allowed by
clearing the
Encrypt All Web Communication
checkbox.
To support the use of HTTPS communications, a Jetdirect certificate must be installed. A factory-default,
self-signed certificate is pre-installed for initial use. Click the
Configure
button to update the pre-installed
certificate, or to install a new one. For more information, see
Configuring Certificates on page 88
.
The minimum encryption strength that will be allowed must be specified when using a Jetdirect
certificate. You may select
Low
(default),
Medium
, or
High
encryption strength. For example, selecting
Low
will allow medium or high encryption levels to be used whereas selecting
High
will only allow high
encryption levels.
For each encryption strength, ciphers are specified to identify the weakest cipher allowed.
NOTE:
Cipher suites support different levels of encryption strength. The cipher suites currently
supported for encryption and decryption are DES (Data Encryption Standard, 56-bit), RC4 (40-
bit or 128-bit), and 3DES (168-bit).
ENWW
Networking Tab
91
Summary of Contents for 635n - JetDirect IPv6/IPsec Print Server
