HP 5130 EI Switch Series Installation Manual Download Page 53 | Manualshive

Page: 53 / 70

background image

49

NOTE:

HP recommends that you use HP 1000 Mbps SFP transceiver modules, SFP+ transceiver modules, or SFP+
DAC cables for the SFP+ ports on the switch. The HP 1000 Mbps SFP and SFP+ transceiver modules are

subject to change over time. For the most up-to-date list of SFP and SFP+ transceiver modules, contact your
HP sales representative or technical support engineer.

For more information about the 1000 Mbps SFP transceiver modules, SFP+ transceiver modules, and
SFP+ DAC cables, see

HP Comware-Based Devices Transceiver Modules User Guide

.

Figure 52

SFP+ DAC cable

(1) Connector

(2) Pull latch

Combo interface

The HP 5130-24G-SFP-4SFP+ EI switch provides eight combo interfaces. A combo interface includes an
SFP port and a 10/100/1000Base-T autosensing Ethernet port. Only one of these two ports can operate
at a time.

LEDs

System status LED

The system status LED shows the operating status of the switch.

Table 19

System status LED description

LED mark

Status

Description

SYS

Steady green

The switch is operating correctly.

Flashing green

The switch is performing power-on self test (POST).

Steady red

The switch has failed POST.

Flashing yellow

Some ports have failed POST.

Off

The switch is powered off.

1

2

«
...
51
52
53
54
55
...
»

Summary of Contents for 5130 EI Switch Series







































































Reviews:

No comments

Related manuals for 5130 EI Switch Series

Brand: KELCO Pages: 22

Brand: Accedian Pages: 2

Brand: BABBITT Pages: 14

Brand: BABBITT Pages: 10

Brand: Radial Engineering Pages: 12

Brand: Maipu Pages: 21

Brand: Maico Pages: 56

RackSwitch G8264T

Brand: IBM Pages: 20

Underwater Switch 24V DC/DMX/02

Brand: Oase Pages: 40

Brand: Manhattan Pages: 2

Brand: steute Pages: 20

Sierra Video 1208V3S

Brand: Kramer Pages: 2

Brand: protech Pages: 4

Brand: Metrix Pages: 12

CT.TS005.003902

Brand: Talkswitch Pages: 309

Brand: Conceptronic Pages: 7

Brand: Nextech Pages: 4

SICOM3028GP Series

Brand: KYLAND Technology Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands