HP 5130 EI Switch Series Installation Manual Download Page 60

Page: 60 / 70

LED

Status

Description

Flashing

The port is sending or receiving data at 10 Gbps.

Off

•

No transceiver module is installed in the port, or no
10 Gbps link is present on the port.

•

The port mode LED is operating in PoE mode

(applicable to the PoE switch models.)

Yellow LED

Steady on

A transceiver module is installed in the port. The port is
operating at 1 Gbps, and a link is present on the port.

Flashing (not 3 Hz)

The port is sending or receiving data at 1 Gbps.

Flashing (3 Hz)

The port has failed POST.

Off

•

No transceiver module is installed in the port, or no
1 Gbps link is present on the port.

•

The port mode LED is operating in PoE mode

(applicable to the PoE switch models.)

Summary of Contents for 5130 EI Switch Series







































































Search results

Summary of Contents for 5130 EI Switch Series

Reviews:

Related manuals for 5130 EI Switch Series

Brands by name

Popular brands

HP 5130 EI Switch Series, Installation Manual

Search results

Summary of Contents for 5130 EI Switch Series

Reviews:

Related manuals for 5130 EI Switch Series

Brands by name

Popular brands