HP 5130 EI Switch Series Installation Manual Download Page 55

Page: 55 / 70

10/100/1000Base-T autosensing Ethernet port LED

•

The HP 5130-48G-2SFP+-2XGT EI, HP 5130-48G-PoE+-2SFP+-2XGT (370W) EI, HP
5130-24G-SFP-4SFP+ EI, HP 5130-48G-4SFP+ EI, HP 5130-48G-4SFP+ EI BR, HP

5130-48G-PoE+-4SFP+ (370W) EI, and HP 5130-48G-PoE+-4SFP+ (370W) EI BR switches provide
a double-color (green and yellow) LED for each 10/100/1000Base-T autosensing Ethernet port to

indicate its operating status.

Table 23

10/100/1000Base-T autosensing Ethernet port double-color LED description

Switch model

Port mode

LED (Mode)

status

Double-color

(green and

yellow) LED

status

Description

•

HP 5130-48G-4SFP+ EI

•

HP 5130-48G-4SFP+ EI

•

HP 5130-24G-SFP-4SFP+

•

5130-48G-2SFP+-2XGT

N/A

Steady green

The port is operating at 1000 Mbps,
and a link is present on the port.

Flashing green The port is sending or receiving data at

1000 Mbps.

Steady yellow

The port is operating at 10/100 Mbps,
and a link is present on the port.

Flashing yellow
(not 3 Hz)

The port is sending or receiving data at
10/100 Mbps.

Flashing yellow
(3 Hz)

The port has failed POST.

Off

No link is present on the port.

•

HP
5130-48G-PoE+-4SFP+
(370W) EI

•

5130-48G-PoE+-4SFP+
(370W) EI BR

•

5130-48G-PoE+-2SFP+-2
XGT (370W) EI

Steady
green (rate

mode)

Steady green

The port is operating at 1000 Mbps,
and a link is present on the port.

Flashing green

The port is sending or receiving data at
1000 Mbps.

Steady yellow

The port is operating at 10/100 Mbps,
and a link is present on the port.

Flashing yellow
(not 3 Hz)

The port is sending or receiving data at
10/100 Mbps.

Flashing yellow
(3 Hz)

The port has failed POST.

Off

No link is present on the port.

Flashing
green (PoE
mode)

Steady green

The port is supplying PoE correctly.

Flashing green
(3 Hz)

•

The PD power requirement exceeds

the port PoE capacity.

•

The port fails to meet the power

requirement of the PD because of

power insufficiency of the switch.

Steady yellow

A non-PD device is attached to the port,
or the port is experiencing a PoE failure.

Flashing yellow
(3 Hz)

The port has failed POST.

Summary of Contents for 5130 EI Switch Series







































































Search results

Summary of Contents for 5130 EI Switch Series

Reviews:

Related manuals for 5130 EI Switch Series

Brands by name

Popular brands

HP 5130 EI Switch Series, Installation Manual

Search results

Summary of Contents for 5130 EI Switch Series

Reviews:

Related manuals for 5130 EI Switch Series

Brands by name

Popular brands