HP 5130 EI Switch Series Installation Manual Download Page 50

Page: 50 / 70

Table 14

1/10GBase-T autosensing Ethernet port specifications

Item

Specification

Connector type

RJ-45

Interface attributes

1/10 Gbps, full duplex, MDI/MDI-X autosensing

Transmission medium and max
transmission distance

•

55 m (180.45 ft) over category-6 unshielded twisted pair cable

•

100 m (328.08 ft) over category-6 shielded twisted pair cable

•

100 m (328.08 ft) over category-6A or above twisted pair cable

Compatible standards

•

IEEE 802.3ab

•

IEEE 802.3an

To avoid packet loss caused by interferences, HP recommends that you layer cables as follows:

•

Use category-6A or above cables and connectors.

•

Do not bundle cables in their first 20 m (65.62 ft).

•

Separate power cords and twisted pair cables at and around the distribution frame.

•

For ports adjacent to one another on the device, the peer ports on the distribution frame is
preferably not adjacent, for example:



If the device connects to one distribution frame, connect port 1 on the device to port 1 on the

distribution frame and port 2 on the device to port 3 on the distribution frame.



If the device connects to two distribution frames, connect port 1 on the device to port 1 on
distribution frame 1 and port 2 on the device to port 1 on distribution frame 2.

•

Keep the device and twisted pair cables away from the interference source, such as a two-way
radio and a high-power variable-frequency drive.

100/1000Base-X SFP port

The HP 5130-24G-SFP-4SFP+ EI switch provides 24 100/1000Base-X SFP ports, and you can install the

100 Mbps SFP transceiver modules in

Table 15

and 1000 Mbps SFP transceiver modules in

Table 16

the SFP ports as needed.

Table 15

100 Mbps SFP transceiver modules available for the SFP ports

Product

code

HP description

Central

wavelength

(nm)

Connector

Fiber diameter (µm)

Max

transmission

distance

JD102B

HP X115 100M SFP
LC FX Transceiver

1310

Multi-mode, 50/125

2 km (1.24
miles)

Multi-mode,
62.5/125

JD120B

HP X110 100M SFP
LC LX Transceiver

1310

Single-mode, 9/125

15 km (9.32
miles)

JD090A

HP X110 100M SFP
LC LH40 Transceiver

1310

Single-mode, 9/125

40 km (24.86
miles)

JD091A

HP X110 100M SFP
LC LH80 Transceiver 1550

Single-mode, 9/125

80 km (49.71
miles)

Summary of Contents for 5130 EI Switch Series







































































Search results

Summary of Contents for 5130 EI Switch Series

Reviews:

Related manuals for 5130 EI Switch Series

Brands by name

Popular brands

HP 5130 EI Switch Series, Installation Manual

Search results

Summary of Contents for 5130 EI Switch Series

Reviews:

Related manuals for 5130 EI Switch Series

Brands by name

Popular brands