HP 5130 EI Switch Series Installation Manual Download Page 58

Page: 58 / 70

Table 25

1/10GBase-T autosensing Ethernet port double-color LED description

Status

Description

Steady green

The port is operating at 10 Gbps and a link is present on the port.

Flashing green

The port is sending or receiving data at 10 Gbps.

Steady yellow

The port is operating at 1 Gbps and a link is present on the port.

Flashing yellow (not 3
Hz)

The port is sending or receiving data at 1 Gbps.

Flashing yellow (3 Hz) The port has failed POST.

Off

•

No link is present on the port.

•

The port mode LED is operating in PoE mode (applicable to the PoE switch

models.)

•

The HP 5130-24G-2SFP+-2XGT EI and HP 5130-24G-PoE+-2SFP+-2XGT (370W) EI switches provide
two single-color LEDs for each 1/10GBase-T autosensing Ethernet port to indicate its operating
status.

Table 26

Description for the two single-color LEDs for the 1/10GBase-T autosensing Ethernet port

LED

Status

Description

Green LED

Steady on

The port is operating at 10 Gbps and a link is present on the
port.

Flashing

The port is sending or receiving data at 10 Gbps.

Off

•

No 10 Gbps link is present on the port.

•

The port mode LED is operating in PoE mode (applicable to

the PoE switch models.)

Yellow LED

Steady on

The port is operating at 1 Gbps and a link is present on the
port.

Flashing (not 3 Hz) The port is sending or receiving data at 1 Gbps.

Flashing (3 Hz)

The port has failed POST.

Off

•

No 1 Gbps link is present on the port.

•

The port mode LED is operating in PoE mode (applicable to

the PoE switch models.)

100/1000Base-X SFP port LED

The HP 5130-24G-SFP-4SFP+ EI switch provides a double-color (green and yellow) LED for each
100/1000Base-X SFP port to show its operating status.

Table 27

100/1000Base-X SFP port LED description

Status

Description

Steady green

A transceiver module is installed in the port. The port is operating at 1 Gbps, and
a link is present on the port.

Flashing green

The port is sending or receiving data at 1 Gbps.

Summary of Contents for 5130 EI Switch Series







































































Search results

Summary of Contents for 5130 EI Switch Series

Reviews:

Related manuals for 5130 EI Switch Series

Brands by name

Popular brands

HP 5130 EI Switch Series, Installation Manual

Search results

Summary of Contents for 5130 EI Switch Series

Reviews:

Related manuals for 5130 EI Switch Series

Brands by name

Popular brands