Howard M9 Page 13 Technical & Service Manual Download

Page: 13 / 62

Technical Service Manual M9 Transfer Stretcher (M999-29, Version 11, June 2021)

6. MAINTENANCE & SERVICING

6.1 AUTHORISED SERVICING

WARNING: All inspections, maintenance, servicing and repairs must be carried out either by Howard Wright

Limited, an authorised service dealer, a Howard Wright Limited trained technician or by a competent

person to national legislation and / or standards.

WARNING: Do not modify or tamper with the stretcher or its accessories without written agreement from

Howard Wright Limited.

6.2 ANNUAL INSPECTION

Inspection of the stretcher shall be performed annually in accordance with the maintenance checklist (section 6.5)

and any legal portable appliance testing (PAT) requirements.

6.3 OBTAINING SPARE PARTS & SERVICE

WARNING: All replacement parts must be sourced through Howard Wright Limited.

Howard Wright Limited’s products are supported by an extensive network of authorised service dealers. These service

dealers are trained by Howard Wright Limited. For contact details of your nearest service dealer please contact Howard

Wright Limited or visit our website

howardwrightcares.com

6.3.1 HWL CONTACT DETAILS

Howard Wright Limited is the manufacturer.

• Name:

• Address:

6.3.2 STRETCHER INFORMATION

When making service or repair enquiries, please provide the following information: (refer to page 7)

• Stretcher model (MODEL:).

• Stretcher manufacture date (DATE:).

• Stretcher serial number

This information is recorded on the stretcher serial number label located on the left side at the foot end of the deck frame.

PO Box 3003, Fitzroy

2 Paraite Road, Bell Block

New Plymouth 4341

New Zealand

T. +64 (6) 755 0976

F. +64 (6) 755 0908

[email protected]

Howard Wright Limited

PO Box 2786

Taren Point

NSW 2229

Australia

T. 1800 120 727

F. 1800 120 717

[email protected]

Howard Wright Limited

United Kingdom

T. 0845 094 9894

www.howardwrightcares.co.uk

[email protected]

Howard Wright Limited

Summary of Contents for M9































































Search results

Summary of Contents for M9

Reviews:

Related manuals for M9

Brands by name

Popular brands

Howard M9, Technical & Service Manual

Search results

Summary of Contents for M9

Reviews:

Related manuals for M9

Brands by name

Popular brands