background image

Page 4

21091-0-0606

HW075DV

HW130DV

HW180DV

24 5/64”

12 15/16”

19 39/64”

25 19/32”

5 1/32” (HW075DV, HW130DV)
7 1/32” (HW180DV)

UNIT DIMENSIONS

MAKE SURE THAT APPLIANCE IS SUITABLE FOR THE GAS SUPPLY AVAILABLE: 

NATURAL GAS

 

OR 

PROPANE/LP.

Children and adults should be alerted to the hazards of high surface temperatures and should stay away 

to avoid burns or clothing ignition.

Any safety screen or guard removed for servicing must be replaced prior to operating the heater.

Do not use this heater if it has been under water. Immediately call a qualified service technician to inspect 

the heater and to replace any part of the control system and any gas control which has been under water.

Young children should be carefully supervised when they are in the same room as the heater.

Installation and repair should be done by a qualified service person. Heater should be inspected before 

use and at least annually by a qualified service person. 

More frequent cleaning may be required due to excessive lint from carpeting, bedding material etc. It is 

imperative that control compartments, burners, and circulating air passageways of the appliance be kept 

clean.

Follow State and Local codes for installation.

DO NOT put anything around the furnace that will obstruct the flow of combustion and ventilation air.

DO keep the appliance area clear and free from combustible material, gasoline and other flammable va-

pors and liquids.

DO examine venting system periodically and replace damaged parts.

DO make a periodic visual check of pilot and burners. Clean and replace damaged parts.

CAUTION: Pilot hole cover must be kept tightly closed during operation.

Vent cap hot while furnace is in operation.

IMPORTANT SAFETY INFORMATION

Summary of Contents for HW075DVN-1





























Reviews: