background image

Page 26

21091-0-0606

Parts can be ordered

 only

 through your 

service person or dealer.

 For best results, the 

service person or dealer

 should order parts 

through the distributor. Parts can be shipped directly to the 

service person/dealer

.

All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your 

equipment. Then determine the Part Number (

not

 the Index Number) and the Description of each part from the following appropriate 

illustration and list. Be sure to give all this information . . .
Furnace Number  

 

Part Description 

Furnace Serial Number 

 

Part Number  

Type of Gas (Propane or Natural) 
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store. 
Shipments contingent upon strikes, fires and all causes beyond our control.

HOW TO ORDER REPAIR PARTS

The Company reserves the right of introducing any modification deemed convenient in order to improve the products, or due to any 

manufacture or commercial requirements, without previous notice, provided those modifications are in accordance with the local gas 

code.

This manual will help you obtain efficient, dependable service from your HouseWarmer heater, and enables you to obtain repair parts 

correctly.

HOUSEWARMER HEATING APPLIANCE LIMITED WARRANTY

Limited Ten-Year Warranty

Empire promises to the owner that if the combustion chamber (see parts list) fails because of defective work-

manship or material within ten years from the date of purchase, Empire will repair, or at Empire's option, re-

place the defective combustion chamber.

Limited One-Year Warranty

Should any part fail because of defective workmanship or material within one year from the date of purchase, 

Empire will repair or, at Empire's option, replace the defective part.

Duties Of The Owner

The heating appliance must be installed by a qualified installer and operated in accordance with the written 

instructions furnished with appliance.

Ready access to the appliance for service is the responsibility of the owner.

Travel, diagnostic cost, service labor to repair the defective appliance, and freight charges on warranty parts to 

and from the factory will be the responsibility of the owner.

A bill of sale, cancelled check, or payment record should be kept to verify purchase date and establish warranty 

period.

How to Get Service

Service under this warranty must be obtained by contacting your Empire dealer (See telephone directory or call 

(877) 459-1583, Consumer Relations Department, Empire Comfort Systems, Inc.). Provide the dealer with the 

model number, serial number, type of gas and purchase verification information.

If, after contacting your Empire dealer, service received has not been satisfactory, contact: Consumer Relations 

Department, Empire Comfort Systems, Inc., P.O. Box 529, Belleville, Illinois 62222, or call (877) 459-1583 

for assistance.

Your rights under State Law

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to 

state.

Summary of Contents for HW075DVN-1





























Reviews: