Page 37
CARE OF THE SPA COVER
WaRNING:
The vinyl cover is a manual safety cover that meets or exceeds all prevailing requirements of AsTM standards for spa safety
covers when installed and used correctly as of the date of manufacture. Non-secured, or improperly secured covers are a hazard. open the
cover to its fully open position before use.
vInyL Cover
The vinyl spa cover is an attractive, durable foam insulation product. Monthly cleaning and conditioning are recommended to maintain its beauty.
To CLean and CondITIon THe vInyL Cover:
1. Remove the cover from the spa and gently lean it against a wall or fence.
2. With a garden hose, spray the cover to loosen and rinse away dirt or debris.
3. using a large sponge and/or a soft bristle brush, and using a very mild soap solution (one teaspoon dishwashing liquid with two gallons of
water), or baking soda (sodium bicarbonate), scrub the vinyl top in a circular motion. do not let the vinyl dry with a soap film on it before it can
be rinsed clean.
ImpORTaNT:
To avoid soap getting into the spa water, the spa cover should not be on the spa during cleaning.
4. Scrub the cover’s perimeter and side flaps. Rinse clean with water.
5. Rinse off the underside of the cover with water only (use no soap), and wipe it clean with a dry rag.
6. To condition the cover after cleaning, apply a thin film of
Hot Spring
cover shield to the vinyl surface and buff to a high luster.
SERVICE NOTE: T
o remove tree sap, use cigarette lighter fluid (not charcoal lighter fluid). use sparingly, and rinse with saddle soap solution
immediately afterwards, then wipe dry.
Important reminders:
• DO
remove snow buildup to avoid breakage of the foam core from the additional weight of the snow.
• DO
lock cover straps to secure the cover when the spa is not in use.
• DO NOT
drag or lift the spa cover using either the flaps, or the tie-down straps.
• DO NOT
walk, stand, or sit on the cover.
• DO NOT
place any metal or heat transferring object on the cover or place any type of plastic tarp or drop cloth over the cover as this may
result in a melted foam core, which would not be covered under the warranty.
•
DO NOT
use any lifting mechanisms, chemicals, or cleaners except those recommended by Watkins Manufacturing corporation, or its
Authorized sales and service dealer.
ImpORTaNT:
Whenever the spa is not in use, it is essential that the cover be in place. When filled, this ensures effective temperature
maintenance and economical operation. When empty, this prevents potential damage to the surface finish of the interior walls, which can
result from the excessive heat of the sun. This type of damage is specifically excluded from warranty coverage.
COVER lIFTER SYSTEMS
clearance required behind cover when open:
• CoverCradle
®
& CoverCradle II - 24”
• UpRite
®
- 7”
• Lift ’n Glide
®
- 14”
ImpORTaNT:
use of a cover lifter other than those listed above will void the
Hot Spring
spa cabinet warranty. cover lifers must be installed to open
back-to-front. Installing a cover lifter to open side-to-side will void the
Hot Spring
spa cabinet warranty. see Limitations section of the
Hot Spring
spa warranty.
HoW To oPen THe vInyL Cover
NOTE:
Never attempt to open or remove the vinyl cover by grasping or pulling on the skirting or cover lock straps. The skirting will tear, and torn
skirting is not covered under the terms of the warranty.
check for ice build-up around the gas springs and pivot points of the retractable cover system. Ice buildup may damage system components.
WaRNING:
The vinyl cover and retractable cover system are not recommended for use in wind conditions reaching above 25 mph (40 kmh).
NOTE:
If your spa is located in an area susceptible to high winds, additional cover lock straps may be installed to minimize wind damage to the cover.
HoW To oPen THe Cover
1. With the cover lock straps unfastened, place one hand under the cover skirting, between the spa and cover, to break the cover’s vacuum seal.
Then, fold the front half of the cover over onto the back half.
2. If no rear access is available, stand to the side of the spa directly adjacent to the hinge area of the folded cover.
A.
For the CoverCradle
®
& CoverCradle II retractable cover systems:
using both hands, cup one hand under the lower half of the cover
(just above the water) and place the other along the side of the cover, just above the skirt. Gently push (do not lift) with both hands towards
the opposite rear corner of the cover (diagonally). As the cover opens, the gas springs will allow the cover to come to a gentle stop.
B.
For the UpRite
®
retractable cover systems:
simply lift the cover at its center hinge, allowing it to move to the back of the spa and to
gently rest there.
Page 37
Spa Care and Maintenance
Summary of Contents for Limelight
Page 1: ......