Page 34
Spa Care and Maintenance
Page 34
Spa Care and Maintenance
“oFF
”buttons simultaneously a second time the screen will go back to it’s original display.
SpA cARE ANd MAINTENANcE
your
Hot Spring
®
spa is manufactured from the highest quality, most durable materials available. even so, the spa care and maintenance program
you develop will ultimately determine how long your spa, and its individual components, will last. Regular maintenance and following the advice in
this section will help you to protect your investment.
dRAININg THE WATER
Detergent residues from bathing suits and soap film from your body may gradually accumulate in your spa’s water. Normally, in about four months
the water will become sudsy and should be replaced. showering without using soap prior to entering the spa, and using only the rinse cycle when
laundering your bathing suit, will help to reduce detergent residue in the spa water.
ImpORTaNT:
Remember to change your water every three to
four months.
To draIn yoUr SPa:
1. disconnect the spa from the power supply by tripping both of the GFcI breakers located in the subpanel.
2. Locate the drain valve for the spa and remove the drain cap. Attach the inlet of a garden hose to the drain valve (to avoid flooding of the
foundation surrounding the spa) and route the outlet of the hose to an appropriate draining area.
NOTE:
spa water with a high sanitizer level may harm plants and grass.
3. open the valve by turning the knob. The spa will drain by gravitational flow.
ImpORTaNT:
All
Hot Spring
spa models will drain almost completely through the main drain valve. equipment such as the jet pump and
heating system will drain. Any water remaining within the plumbing or equipment after draining will only need to be removed if the spa is being
winterized.
4. Allow all of the water to drain through the drain.
5. When empty, inspect the spa shell and clean as required. (Follow the care of the exterior instructions.)
6. close the drain valve and reinstall the drain cap.
7. Refill the spa through the filter compartment BeFoRe restoring power.
PREVENTION OF FREEZINg
your spa has been designed and engineered for year-round use in any climate. In some areas, extremely cold temperatures (below 10°F)
combined with strong wind, may cause partial freezing of the jet pump, even though the water inside the spa remains at the selected temperature.
The energy efficiency of the spa may also decrease during these cold periods, as the heater will cycle more frequently. As an additional precaution
against partial freezing of some of the components, the equipment compartment can be insulated with an insulating kit (available from your local
dealer). This insulating kit will also help to maximize the spa’s energy efficiency.
NOTE:
When warmer weather returns (approx. 60°-70°F), the insulating kit MusT be removed to prevent overheating of the jet pump.
WInTerIZIng yoUr SPa
If you leave the spa unused for a long period of time in severely cold weather, you should drain the spa and winterize it to avoid accidental freezing
due to a power or equipment failure.
DaNGER:
use only Propylene Glycol as your anti-freeze (available at most RV or marine supply stores). This is non-toxic. Never use an
automobile anti-freeze (ethylene Glycol) since it is toxic!
WaRNING:
Failure to follow these instructions correctly can lead to freeze damage not covered by warranty. It is strongly recommended that
you contact your local dealer to perform this service
1. Drain your spa following the Draining the Water section in the owner’s manual.
2. Remove the filter cartridge, clean and store in a dry place.
ImpORTaNT:
These additional instructions must be utilized when draining and winterizing your spa in climates where the temperature falls below
32°F (0°c). A five (5) gallon combination (vacuum/blower) wet/dry shop vac must be used to effectively remove water that is trapped inside the
plumbing lines.
3. Attach the vacuum’s hose to the blower side of the shop vac.
a) Place the end of the vacuum hose down the filter opening.
b) Turn on the blower function and allow it to blow out any water remaining in the plumbing lines (approximately 3 to 5 minutes).
c) Turn the smartJet® lever to the second position and allow that system to purge.
Summary of Contents for Limelight
Page 1: ......
