Page 21
JETS
dIreCT HydroMaSSage JeTS
direct Hydromassage jets are small, producing a precisely narrow stream of massaging action. They are placed in groups to
perform a soft, soothing massage on your back, neck, and shoulders.
CoMbInaTIon HydroMaSSage JeTS
These jets deliver a great massage to the feet, back and shoulder areas. These jets may be adjusted to provide either a
stationary, direct stream, or, by positioning the nozzle to one side, a variety of rotating massage patterns. Also, the speed of
the rotation can be changed by rotating the jet faceplate from a full stream, to shutting the jet completely off. To avoid damage
to your spa’s plumbing and components, do not turn off more than half of these jets at the same time.
CoMbInaTIon XL HydroMaSSage JeTS
These large jets may be adjusted to provide either a stationary, direct stream, or, by positioning the nozzle to one side,
a variety of rotating massage patterns. Also, the speed of the rotation can be changed by rotating the jet faceplate from
a full stream, to shutting the jet completely off. To avoid damage to your spa’s plumbing and components, do not turn off
more than half of these jets at the same time.
CoMbInaTIon JeTS MaInTenanCe
If you notice that either the combination or combination XL jets spin slower than when the spa was new, or the jets are sticking, the cause may be
built-up deposits inside the jet bearings. To remove the deposits, use the following instructions:
1. With the spa off, rotate the combination jet face counter-clockwise until it stops.
2. once the face stops rotating, push in and use a little extra force to rotate the face even more counter-clockwise past the locking position until it
stops. Pull face with the body away from the spa.
3. After flushing the bearing inside the body with water, spin the rotating eye, it should spin very freely. If it does not, place the bearing end in a cup
of vinegar (the vinegar will soften any deposits). Leave soaking overnight. The next day, flush with water and repeat the spin test.
NOTE
: If it still doesn’t spin freely, a second night of soaking is required. If the bearing still does not spin, you will need to purchase a
replacement assembly from your
Hot Spring
®
dealer.
4. To replace, position the cutout at the back end of the face body downward and push the face body back into the spa fitting. slightly rotate face
body in either direction until you feel the body align with the fitting, then press firmly on the face body. once seated, push and rotate the face
clockwise using a little extra force to overcome the locking position. If the face does not rotate, remove and rotate face body 180° and repeat
this step. Turn the jet pump on, the combination jet should spin freely.
MoTo-MaSSage
®
dX JeT (gLeaM
™
onLy)
The Moto-Massage dX automatically travels two streams up and down in a sweeping motion, simulating the natural stroking effects of a manual
massage. The intensity of the Moto-Massage dX jet may be adjusted by turning the comfort control lever.
The Moto-Massage dX jet has been factory adjusted to provide maximum hydromassage, and to achieve full vertical travel with its comfort
control lever in the full air volume position. should the Moto-Massage dX jet not achieve full vertical travel and the problem is not a closed air
control valve or clogged filter cartridge, then your Hot spring service center should be contacted.
SERVICE NOTE:
A slow or non-moving Moto-Massage dX jet may indicate that the filter cartridge pores are obstructed with dirt, body oils, or
calcification. Follow the filter cartridge cleaning procedures in the spa care and Maintenance section of this manual.
WATER FEATURE
The Gleam, Pulse
®
, Flair
®
, and Glow
®
spas come equipped with a Vidro
®
water feature. This water feature can be turned on or off when the two-
speed pump is on low speed (tranquil mode) or high speed. To function correctly, the water feature on/off lever must be placed in the full on position
only.
If the lever is not in the full on position when the pump is on high speed, it is likely that the water feature will project water substantially farther out
into the spa as the on/off lever is opened. This is not proper operation. If this occurs, the pump should be turned off, the water feature lever rotated
to the full on position and the pump turned on again.
When not in use turn the on/off lever to the oFF position.
CAUTION:
Partial blockage of water flow at entrance of water feature will cause the water to flow farther into or over the spa.
Page 21
Page 21
operating Instructions
Summary of Contents for Limelight
Page 1: ......
