1
6
G
B
Before connecting to the power suppl
y
, make sure
that:
the appliance is earthed and the plug is compliant
with the law.
the socket can withstand the maximum power of
the appliance, which is indicated on the data
plate (
see below
).
the voltage is in the range between the values
indicated on the data plate (
see below
).
the socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it.
Do not use extension cords or multiple sockets.
Once the appliance has been installed, the power
suppl
y
cable and the electrical socket must be
easil
y
accessible.
The cable must not be bent or compressed.
The cable must be checked regularl
y
and replaced
b
y
authorised technicians onl
y
(
see Assistance
).
The manufacturer declines any liability should these
safety measures not be observed.
G
as
c
onne
c
tion
The appliance should be connected to the main gas
suppl
y
or to a gas c
y
linder in compliance with
current National regulations. Before carr
y
ing out the
connection, make sure the cooker is compatible with
the gas suppl
y
y
ou wish to use. If this is not the
case, follow the instructions indicated in the
paragraph Adapting to different t
y
pes of gas.
When using liquid gas from a c
y
linder, install a
pressure regulator that complies with current
National regulations.
Check that the pressure of the gas suppl
y
is
consistent with the values indicated in Table 1
(Burner and nozzle specifications) since this will
ensure the safe operation and longevit
y
of
y
our
appliance while maintaining efficient energ
y
consumption.
Should
y
ou need to install a gas hob on top of a
built-in gas oven, it is strictl
y
forbidden to connect
the two or to use a single cut-off tap. The two
appliances should be connected separatel
y
, and
each one should have its own stop tap in order to
make them completel
y
independent from one
another (
see figures
).
C
o
nn
e
c
ti
o
n
w
it
h
a
r
i
g
i
d
p
i
p
e
(
copp
e
r
or
s
t
eel
)
Connection to the gas s
y
stem must be carried out
in such a wa
y
as not to place an
y
strain of an
y
kind
on the appliance.
There is an adjustable L-shaped pipe fitting on the
appliance suppl
y
ramp and this is fitted with a seal in
order to prevent leaks. The seal must alwa
y
s be
replaced after rotating the pipe fitting (the seal is
provided with the appliance). The gas suppl
y
pipe
fitting is a threaded 1/2 gas c
y
lindrical male
attachment.
C
o
nn
e
c
tin
g
a
f
le
x
i
b
le
j
o
int
less
s
tain
less
s
t
eel
p
i
p
e
t
o
a
t
hr
e
a
d
e
d
atta
chm
e
nt
The gas suppl
y
pipe fitting is a threaded 1/2 gas
c
y
lindrical male attachment.
These pipes must be installed so that the
y
are never
longer than 2000 mm when full
y
extended. Once
connection has been carried out, make sure that the
flexible metal pipe does not touch an
y
moving parts
and is not compressed.
Onl
y
use pipes and seals that compl
y
with current
National regulations.
C
h
e
c
k
in
g
t
h
e
ti
gh
tn
ess
o
f
t
h
e
co
nn
e
c
ti
o
n
When installation has been completed, check the
pipe fittings for leaks using a soap
y
solution. Never
use a flame.
A
d
a
p
tin
g
t
o
d
i
ff
e
r
e
nt
t
y
p
es
o
f
g
a
s
In order to adapt the oven to a t
y
pe of gas other
than the t
y
pe for which it was manufactured
(indicated on the label), follow these simple steps:
Replacing the oven burner nozzle
1. Open the oven door full
y
.
2. Slide out the bottom of the
oven.
NO
OK
