manualshive.com logo in svg

HORN LHD6001+, Installation Manual, Page: 30 / 36

Share
Download
HORN LHD6001+ Installation Manual Download Page 30

-

26

-

APPENDIX

Protocol Code 

Code

100

110

121

131

132

133

134

137

151

301

302

00

02

21~24

04~10

11~17

1~8

1~8 wired zone

98

Medical Alarm

Fire Alarm

Duress Alarm

Perimeter Alarm

Interior Alarm

24 hour Alarm

Entry / Exit Alarm

Tamper Alarm

Gas detected Alarm

AC loss trouble

Low system battery trouble

Between the panel and CMS there are two format codes: ADEMCO 4+1

、

ADEMCO Contact ID.

The following table defines the Event Codes used in this protocol:

Event

Code Event

320

382

145

401

409

441

442

521

570

602

Sounder Trouble

Loss of Keypad trouble

Keypad temper Alarm

Arm / Disarm by user

Keyswitch arm/ disarm,user NO = Zone No

Armed STAY

Keyswitch armed STAY, user NO = Zone No

Bell Disable

Zone bypass, All zones bypass or cancel bypass when the 
Zone NO = 99

Periodic test report

ADEMCO Contact ID: The following table defines the user Codes used in Arming/disarming

Code

Event

Operation using keypad without user code, such as arm-away, from disarm to arm-stay

Disarming by user with master code on the keypad or on the telephone

Arming/ disarming by normal user with code from 1 to 7

Arming / disarming used from keyfob 1 to keyfob 7

Arming/ disarming via phone number 5-8 during alarm

A disarming information before Duress alarm is sent, when disarming by the user with Duress code.
 The number is 98

ADEMCO Contact ID Operation definition when using keyswitch zone:

Code

Event

Summary of Contents for LHD6001+





































Reviews:

No comments