manualshive.com logo in svg

Horizon Fitness CRF-362, User Manual

Share
Download
Horizon Fitness CRF-362 User Manual Download Page 106

106

CRF-362

5-4 

Replacing the Creasing Unit

This section explains the procedure for replacing the creasing unit. The optional creasing units, which can 
make creases of different width, are available. The 1st creasing unit will be used as an example in this section. 
The procedure also applies to the 2nd creasing unit.

1st Creasing Unit 2nd Creasing Unit

Standard Creasing 

Unit

0.8 mm 
0.031"

0.8 mm 
0.031"

Optional Creasing 

Unit

Thin: 0.5 mm 
 0.020"

Thick: 2.0 mm 
 0.079"

Thick: 2.0 mm 
 0.079"

Accessories 

Creasing Unit

Thick: 1.3 mm 
 0.051"

Thick: 1.3 mm 
 0.051"

1 

Turn off the Power switch.

2 

Open the register transport sec-

tion cover.

3 

Open the fold section cover.

13130

50401A1

1st Creasing Unit

2nd Creasing Unit

13130

50401B1

Register Transport Section Cover

Pull here to open the cover.

13130

50401C1

Fold Section 

Cover

Summary of Contents for CRF-362



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands