background image

Contents 

1.

 

Outline ...................................................................................................................... 1

 

2.

 

Specifications ............................................................................................................ 1

 

3.

 

External Dimensions ................................................................................................. 3

 

4.

 

Operating Procedures ............................................................................................... 5

 

4-1

 

Piping and electric wiring ..................................................................................... 5

 

4.2

 

Startup and warm-up ........................................................................................... 6

 

4.3

 

Vaporization ......................................................................................................... 7

 

5.

 

Peripheral Equipment ............................................................................................... 7

 

6.

 

Procedures for Disconnecting Valve Cable and Heater Cable Connectors .............. 8

 

7.

 

Troubleshooting ........................................................................................................ 8

 

8.

 

Instructions for Handling ......................................................................................... 11

 

9.

 

Other Instructions for Use ....................................................................................... 12

 

9.1

 

Entry of air bubbles into liquid supply line .......................................................... 12

 

9.2

 

Clogging by vaporization.................................................................................... 13

 

9.3

 

Pressure loss of internal nozzles ....................................................................... 14

 

9.4

 

Valve travel for set temperature ......................................................................... 14

 

9.5

 

Purging procedures ........................................................................................... 14

 

9.6

 

Temperature control .......................................................................................... 14

 

9.7

 

Setting of pressure of liquid supply tank ............................................................ 14

 

9.8

 

Moisture contents (dew points) of carrier gas and purging gas .......................... 15

 

9.9

 

Carrier gas and liquid supply pressure .............................................................. 15

 

10.

 

Example of Preparation of Secondary Heating Piping ............................................ 15

 

11.

 

Examples of Temperature Regulator Wiring ........................................................... 16

 

12.

 

CHEMICAL CONTENT INFORMATION(The Six China RoHS Restricted 

Materials)Example of Preparation of Secondary Heating Piping ................................... 17

 

 

 

Summary of Contents for MV-2000






















Reviews: