manualshive.com logo in svg

Honeywell Satellite XT 9602-0200 4-20 mA, Operation Manual

Share
Download
Honeywell Satellite XT 9602-0200 4-20 mA Operation Manual Download Page 52

Satellite XT 4-20 mA Versions

7.1.2 

Faults

 

Instrument faults refer to a problem which prevents the instrument from operating properly 

 

and interferes with the ability to monitor or document concentration alarms.

 

 

If the instrument has detected an instrument fault, a fault signal of a defined output current

 

 

for each different fault condition is sent to attached control systems. The green status LED 

 

is off. The LCD display is flashing while indicating the specific fault message.

Fault - ADC Not Ready !

This indicates that there is a problem with the internal
electronics. The AD Converter has failed.
Switch power supply for this unit off and on again. If the
instrument still shows this message, switch off power supply 
for this unit and contact MST for further instructions.
Output current is 2.0 mA.

Fault - No Sensor !

This message indicates that no sensor is inserted or that a
sensor type not suitable for the Satellite is used.
To eliminate the problem, insert the correct sensor.
When using the Satellite in combination with the sensor

extension, make sure that all connections are firmly attached.

Output current is 1.8 mA.

 

Fault - Wrong Sensor !

This message indicates that the sensor installed is not the
sensor assigned to this particular instrument.
To correct the problem, insert the sensor assigned and
documented to this instrument. The data are stated in the test

certificate provided with the shipment.

Output current is 1.6 mA.

Fault - Replace Sensor !

This message indicates that the sensor presently installed is
depleted (the warning CHECK SENSOR ! has been ignored).
To correct the problem, replace the old sensor immediately.
Output current is 1.4 mA. 

! This function is not available for instruments with
oxygen sensor or catalytic sensor.

- - - - F AU L T - - - -

ADC NOT RE ADY !

- - - - F AU L T - - - -

NO S ENSOR !

- - -

WR

-

ON

F A

G

U L

S E

T

NS

- -

OR

- -

!

- - - - F AU L T - - - -

RE P L ACE S ENSOR !

7-2

Troubleshooting - Section 7

Summary of Contents for Satellite XT 9602-0200 4-20 mA










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands