Honeywell NOTIFIER UDACT-2 Instruction Manual Download Page 5

Page: 5 / 52

UDACT-2 — Instruction Manual

P/N 54089:B3 10/29/2019

Section 1: Overview .......................................................................................................................................................... 7

1.1: Introduction .......................................................................................................................................................................................................7
1.2: UL 864 Compliance...........................................................................................................................................................................................7

1.2.1: Products Subject to AHJ Approval.........................................................................................................................................................7
1.2.2: Programming Features Subject to AHJ Approval ..................................................................................................................................7

1.7: Board Layout ...................................................................................................................................................................................................10

Section 2: Installation and Wiring.................................................................................................................................. 13

Section 3: Programming ................................................................................................................................................. 23

Section 4: Operation ....................................................................................................................................................... 28

4.1: Switches...........................................................................................................................................................................................................28

4.2: Telephone Line Testing....................................................................................................................................................................................28

Section 5: Reporting Formats ........................................................................................................................................ 29

Section 6: Compatible UL Listed Receivers ................................................................................................................. 33

6.1: UL Listed Receivers ........................................................................................................................................................................................33

Appendix A: Panel-Specific Information ....................................................................................................................... 34

A.1: AFP-200 ..........................................................................................................................................................................................................34

A.2: AFP-300/AFP-400 ..........................................................................................................................................................................................35

A.3: NFS2-640 (UL 864 10th), NFS-320/SYS (UL 864 10th), NFS-640 (UL 8th) ...............................................................................................37

A.3.1: General.................................................................................................................................................................................................37

Summary of Contents for NOTIFIER UDACT-2





















































Search results

Summary of Contents for NOTIFIER UDACT-2

Reviews:

Related manuals for NOTIFIER UDACT-2

Brands by name

Popular brands

Honeywell NOTIFIER UDACT-2, Instruction Manual

Search results

Summary of Contents for NOTIFIER UDACT-2

Reviews:

Related manuals for NOTIFIER UDACT-2

Brands by name

Popular brands