Honeywell NOTIFIER UDACT-2 Instruction Manual Download Page 46

Page: 46 / 52

UDACT-2 — Instruction Manual

P/N 54089:B3 10/29/2019

Panel-Specific Information

NFS2-3030 (UL 864 10th), NFS-3030 (UL 8th)

Notes

Recommended wire is 12 AWG (3.25mm

) to 18 AWG (0.75mm

), twisted pair, shielded cable. Connect only one end of shield: a)

shield may be connected to cabinet (earth ground) at fire alarm panel, or b) shield may be connected to Common on TB2 on the

UDACT-2.

Conduit is required for external wire runs. Consult local building codes.

Refer to "Specifications" on page 8 for power requirements.

Below is a remote installation of a UDACT-2 with an NFS-3030 using power supplied by the control panel:

NOTE:

The shield end that is not connected should be insulated to prevent accidental grounding. Do not connect both ends of shield

under any circumstance since a ground fault may result.

udact

-3

0_a.

CAB-3/4 Series Cabinet

To supervised

phone lines

Solid earth ground

EIA-485

(ACS Mode)

TB7 on

control panel

+24 VDC

non-resettable

power

TB6 on control

panel

Wires in

conduit

Remote Cabinet

Figure A.14 UDACT-2 and NFS-3030

Summary of Contents for NOTIFIER UDACT-2





















































Search results

Summary of Contents for NOTIFIER UDACT-2

Reviews:

Related manuals for NOTIFIER UDACT-2

Brands by name

Popular brands

Honeywell NOTIFIER UDACT-2, Instruction Manual

Search results

Summary of Contents for NOTIFIER UDACT-2

Reviews:

Related manuals for NOTIFIER UDACT-2

Brands by name

Popular brands