Honeywell NOTIFIER UDACT-2 Instruction Manual Download Page 14

Page: 14 / 52

UDACT-2 — Instruction Manual

P/N 54089:B3 10/29/2019

Installation and Wiring

Installation Options



NFS2-640 Chassis Mounting

The UDACT-2 is installed on the NFS2-640 chassis within the NFS2-640 backbox as described and shown below:



CHS-M2 Chassis Mounting

The UDACT-2 is installed on a CHS-M2 Chassis within the NFS-640 control panel backbox as described and shown below:



CHS-4

The UDACT-2 may be mounted in the CHS-4 chassis within the control panel backbox as described and shown below.

Step

Action

Disconnect AC power and disconnect batteries.

Position the UDACT-2 on the standoffs and fasten with #4-40 screws.

NOTE:

The UDACT-2 can be mounted in the fourth column of the NFS2-640 Chassis. Be sure to mount the chassis to the

backbox before mounting the UDACT-2.

Step

Action

Disconnect AC power and disconnect batteries.

Insert the tab at the bottom of the board into the chassis slot as indicated.

Position the UDACT-2 on the standoffs and fasten with #4 screws.

UDA

CT-2

CHS

2-M

2.wmf

NFS2-640

Chassis

#4-40 screws

standoff locations

Note

: Mount chassis to backbox before

installing the UDACT-2.

UDACT-2

Figure 2.2 NFS2-640 Chassis Installation

UDA

CT-2

.wmf

Chassis slot

Tab

Fastening holes

Metal standoffs

Figure 2.3 CHS-M2 Installation

UDA

CT-2

-ch

Step

Action

Disconnect AC power and disconnect batteries.

Insert the tab at the bottom of the board into the chassis slot as indicated.

Position the UDACT-2 on the standoffs and fasten with #4 screws.

Summary of Contents for NOTIFIER UDACT-2





















































Search results

Summary of Contents for NOTIFIER UDACT-2

Reviews:

Related manuals for NOTIFIER UDACT-2

Brands by name

Popular brands

Honeywell NOTIFIER UDACT-2, Instruction Manual

Search results

Summary of Contents for NOTIFIER UDACT-2

Reviews:

Related manuals for NOTIFIER UDACT-2

Brands by name

Popular brands