Honeywell NOTIFIER UDACT-2 Instruction Manual Download Page 28 | Manualshive

Page: 28 / 52

background image

UDACT-2 — Instruction Manual

P/N 54089:B3 10/29/2019

28

Section 4: Operation

4.1 Switches

4.1.1 SW1 - Option Select Switch

This DIP switch gives the user four UDACT-2 settings.
•

Switch DIP1 - Download App mode.
Set to ON prior to downloading an application file. Set to OFF when

download is complete.

•

DIP2 - Download Database mode.
Set to ON prior to downloading a database file. Set to OFF when download

is complete.

•

Switch DIP3 - Piezo.
Set to ON to have the piezo sound when an error occurs in self-test mode, or when the UDACT-2 is in trouble.

•

Switch DIP4 - EIA-485 Termination
Set to ON to enable a 120 Ohm terminating resistor on the EIA-485 bus. This setting is required if the UDACT-2 is the only or last

device on the bus.

4.1.2 SW 2 - Trans Clear Button

Press and hold this button switch down for over 3 seconds to immediately stop UDACT-2 transmissions, hang up from the telephone net-
work, clear out any messages that were waiting for transmission, and reset, and return to normal system processing.

4.1.3 SW 3 - Test Report Button

Press and hold this button switch down for over 3 seconds to have the UDACT-2 transmit a test message to both Central Stations. The
message reported is the same as the automatic test message for all formats except Ademco Contact ID.

4.1.4 SW 4 - Reset Button

Press and hold this button switch down for a hardware reset.

4.2 Telephone Line Testing

Connect your telephone test set across a modular test adapter to test for a dial tone.

NOTE:

DIP1 and DIP2 may both be ON at the same time. However, the UDACT-2 does not leave bootload mode until

both switches are returned to the OFF position.

ud

act2

swi.wmf

Figure 4.1 SW1 - Option Select Switch

Download Database mode

Download APP mode

Piezo

EIA-485 Termination

!

WARNING:

DO NOT CONNECT TEST EQUIPMENT TO TRANSFORMER T1. DOING SO WILL DAMAGE THE TRANSFORMER.

«
...
26
27
28
29
30
...
»

Summary of Contents for NOTIFIER UDACT-2





















































Reviews:

No comments

Related manuals for NOTIFIER UDACT-2

Brand: MAGNELAB Pages: 2

Beolab transmitter 1

Brand: Bang & Olufsen Pages: 30

Brand: M-system Pages: 3

Brand: Badger Meter Pages: 4

Brand: Alinco Pages: 48

Brand: Xblitz Pages: 76

Brand: Paul Wegener Pages: 8

RC4Magic Series 3 DMXio

Brand: RC4 Pages: 20

Efector 600 TAD081

Brand: IFM Electronic Pages: 25

Brand: GE Pages: 14

Class B Transceiver NAIS-300

Brand: Navico Pages: 24

Trilithic Seeker D Lite

Brand: Viavi Pages: 18

Brand: Kenwood Pages: 52

Brand: TWIG Pages: 2

Mid-Size Transmitter 31.320

Brand: Hubbell Pages: 2

Brand: EXCLUSIVE Pages: 3

Brand: B&C Speakers Pages: 1

Brand: Broadxent Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands