manualshive.com logo in svg

Honeywell NOTIFIER LDM Series, Instruction Manual, Page: 5 / 68

Share
Download
Honeywell NOTIFIER LDM Series Instruction Manual Download Page 5

LDM Series Instruction Manual —

 P/N 15885:H3 8/12/2019

5

Table of Contents

Section 1: Introduction to the LDM-32 Series................................................................................................................. 7

1.1: About This Manual ............................................................................................................................................................................................7
1.2: UL 864 Compliance...........................................................................................................................................................................................7

1.2.1: UL 864 9th and 10th Edition ..................................................................................................................................................................7

1.3: Related Documentation .....................................................................................................................................................................................7

Section 2: LDM Features................................................................................................................................................... 8

2.1: Product Overview ..............................................................................................................................................................................................8
2.2: The LDM-32 ......................................................................................................................................................................................................9
2.3: The LDM-E32..................................................................................................................................................................................................10
2.4: Connectors on the LDM-32 and LDM-E32.....................................................................................................................................................10
2.5: Switches ...........................................................................................................................................................................................................11
2.6: Terminal Blocks ...............................................................................................................................................................................................11
2.7: Cables ..............................................................................................................................................................................................................11
2.8: The LDM-R32 .................................................................................................................................................................................................12

Section 3: Cabinet and Chassis Mounting.................................................................................................................... 13

3.1: Installation Checklist   .....................................................................................................................................................................................13
3.2: External Cabinets.............................................................................................................................................................................................13
3.3: CHS-4L Chassis...............................................................................................................................................................................................13

Section 4: Wiring Considerations .................................................................................................................................. 16

4.1: Limits ...............................................................................................................................................................................................................16
4.2: Wire Runs ........................................................................................................................................................................................................16
4.3: EIA-485 Wiring Specifications........................................................................................................................................................................16
4.4: EIA-485 Shield in Conduit ..............................................................................................................................................................................17
4.5: EIA-485 Shield Not in Conduit .......................................................................................................................................................................17
4.6: EIA-485, Power and Relay Wiring ..................................................................................................................................................................17
4.7: Supervision Input - TB1, Terminals 6 & 7 ......................................................................................................................................................18
4.8: UL Power-Limited Wiring Requirements........................................................................................................................................................18
4.9: Lamp/LED Wiring    ........................................................................................................................................................................................19
4.10: Control Switch Wiring ...................................................................................................................................................................................20

Section 5: Operating the Lamp Driver Module ............................................................................................................. 21

5.1: LAMP TEST/ACKNOWLEDGE....................................................................................................................................................................21
5.2: On Line LED ...................................................................................................................................................................................................21
5.3: Graphic Annunciator Lamps/LEDs .................................................................................................................................................................21

Section 6: LDM Communications .................................................................................................................................. 22

6.1: Receive Only LDM-32s...................................................................................................................................................................................22
6.2: Receive/Transmit LDM-32..............................................................................................................................................................................22

Section 7: Electrical Ratings and Current Calculations .............................................................................................. 23

7.1: Lamp Driver Electrical Ratings .......................................................................................................................................................................23
7.2: Supervision of LDM points .............................................................................................................................................................................23
7.3: Calculating LDM Series Standby and Alarm Currents....................................................................................................................................23

Appendix A: System 500 (UL 8th) .................................................................................................................................. 24

A.1: Capabilities .....................................................................................................................................................................................................24
A.2: System 500 Trouble Indication .......................................................................................................................................................................24
A.3: Installation Requirements ...............................................................................................................................................................................24
A.4: MPS-24BPCC Main Power Supply (System 500 Only) ................................................................................................................................24
A.5: Configuration for the LDM-32 and System 500 ............................................................................................................................................25
A.6: Annunciator Operation....................................................................................................................................................................................25

Appendix B: System 5000 (UL 8th) ................................................................................................................................ 31

B.1: Capabilities......................................................................................................................................................................................................31
B.2: Installation Requirements ...............................................................................................................................................................................31
B.3: MPS-24A Main Power Supply........................................................................................................................................................................32
B.4: MPS-24B Main Power Supply........................................................................................................................................................................32
B.5: Configuration for the LDM-32 and System 5000  ..........................................................................................................................................33
B.6: AIM-200 Point Annunciation..........................................................................................................................................................................34

Appendix C: NFS2-3030 and NCA-2 (UL 9th), AM2020/AFP1010, NFS-3030, or NCA (UL 8th) ................................. 44

C.1: Capabilities......................................................................................................................................................................................................44

Summary of Contents for NOTIFIER LDM Series





































































Reviews:

No comments