manualshive.com logo in svg

Honeywell NOTIFIER LDM Series, Instruction Manual, Page: 37 / 68

Share
Download
Honeywell NOTIFIER LDM Series Instruction Manual Download Page 37

LDM Series Instruction Manual —

 P/N 15885:H3 8/12/2019

37

AIM-200 Point Annunciation

System 5000 (UL 8th)

Figure B.4 illustrates the configuration of LDMs to annunciate alarms for up to 120 zones (no zone troubles) with the first eight points 
(P1 through P8) dedicated to the System 5000unctions listed below. (Control switches do not function in Alarm Only configuration).

Figure B.5 illustrates the configuration of LDMs to annunciate alarms for up to 56 zones (no zone troubles) with the last eight points 
(P57 through P64) dedicated to the System 5000 function annunciations listed below. (Control Switches do not function in Alarm Only 
mode).

J6

J5

OUTPUTS

J7

J8

J5

Address #1

LDM-32

LDM-E32

Address #2

LDM-32

LDM-E32

System Functions *

25   -   32

1   -   8

33   -   40

9   -   16

41   -   48

73   -   80

105   -   112

17   -   24
49   -   56

81   -   88

113   -   120

65   -   72

97   -   104

57   -   64
89   -   96

wire to 

LEDs

view of LDM-32

* System Status Indicators

not 

Notification Circuit #1 ON (Green LED)

System Alarm (Red LED)

Notification Circuit #2 ON (Green LED)

Municipal Tie ON (Red LED)

Alarm Relay ON (Red LED)

*It is assuming this module/expander annunciates points (circuits) 65-128 and is not 

functioning as a Receive Only annunciator.

Figure B.4  Alarm Only Operation Without 8-Point Shift

J6

J5

OUTPUTS

J7

J8

J8

Address #1

LDM-32

LDM-E32

25   -   32

System Functions *

1   -   8

33   -   40

9   -   16

41   -   48

17   -   24
49   -   56

wire to 

LEDs

* System Status Indicators

not 

used

Notification Circuit #1 ON (Green LED)

System Alarm (Red LED)

Notification Circuit #2 ON (Green LED)

Municipal Tie ON (Red LED)

Alarm Relay ON (Red LED)

view of LDM-32

*It is assumed that the '8-Point Shift' will be selected only on systems containing less than 56 

zones/points or a total of 64 annunciator points or less.

Figure B.5  Alarm Only Operation with 8-Point Shift

Summary of Contents for NOTIFIER LDM Series





































































Reviews:

No comments