Honeywell NOTIFIER LDM Series Instruction Manual Download Page 39

Page: 39 / 68

LDM Series Instruction Manual —

P/N 15885:H3 8/12/2019

AIM-200 Point Annunciation

System 5000 (UL 8th)

Figure B.7 illustrates the configuration of LDMs to annunciate alarms and troubles for up to 56 zones with the last eight points (16
LEDs) dedicated to the CPU functions listed below.

OUTPUTS

Alarm

Trouble

OUTPUTS

Address #1

LDM-32

1st LDM-E32

2nd LDM-E32

3rd LDM-E32

1 - 4

17 - 20
33 - 36
49 - 52

9 - 12

25 - 28
41 - 44

13   - 16
29   - 32
45   - 48

5 - 8

21 - 24
37 - 40
53 - 56 System Status Indicators *

view of LDM-32

* System Status Indicators

NAC Ckt #1 ON (Green LED)

NAC Ckt #2 ON (Green LED)
Municipal Tie ON (Red LED)
Alarm Relay ON (Red LED)

NAC Ckt #1 Trbl (Yellow LED)

NAC Ckt #2 Trbl (Yellow LED)

Municipal Tie Trbl (Yellow LED
Alarm Relay Trbl (Yellow LED)

Supervisory (Yellow LED)

not used

Signals Silenced (Yellow LED)

System Trouble (Yellow LED)

System Alarm (Red LED)

not

*It is assumed that the '8-Point Shift' will be selected only on systems

containing less than 56 zones/points.

Figure B.7 Alarm/Trouble Operation with 8-Point Shift

Summary of Contents for NOTIFIER LDM Series





































































Search results

Summary of Contents for NOTIFIER LDM Series

Reviews:

Honeywell NOTIFIER LDM Series, Instruction Manual, Page: 39 / 68

Search results

Summary of Contents for NOTIFIER LDM Series

Reviews: