manualshive.com logo in svg

Honeywell NOTIFIER LDM Series, Instruction Manual, Page: 62 / 68

Share
Download
Honeywell NOTIFIER LDM Series Instruction Manual Download Page 62

62

LDM Series Instruction Manual —

 P/N 15885:H3 8/12/2019

AFP-200 (UL 8th)

Configuration for the LDM-32 and AFP-200

Figure E.2 illustrates configuration of the LDM to annunciate the Active state for up to 56 zones (no zone troubles) with the last eight 
points (P57 through P64) dedicated to the AFP-200 system function LEDs listed below.

Figure E.3 illustrates wiring the LDM to annunciate the active and trouble states for all 99 zones with the first eight points (J5: P1 
through P8 and J6: P1 through P8) dedicated to AFP-200 functions listed below.

J6

J5

OUTPUTS

J7

J8

J8

wire to 
LEDs

25   -   32

System Functions *

1   -   8

33   -   40

9   -   16

41   -   48

17   -   24
49   -   56

Address #1

LDM-32

LDM-E32

* System Status Indicators

System Alarm

not used

View of LDM-32

*It is assumed that the '8-Point 
Shift' will be selected only on 
systems containing less than 56 
software zones or a total of 64 
annunciator points or less.

Figure E.2  Active Status of Software Zones with 8-Point Shift

J6

J5

OUTPUTS

J7

J8

Alarm

Alarm

Alarm

Alarm

Trouble

Trouble

Trouble

Trouble

J6

J5

OUTPUTS

Address #1

LDM-32

1st LDM-E32

2nd LDM-E32

3rd LDM-E32

System Status Indicators*

13   -   16
29   -   32
45   -   48

1   -   4

17   -   20
33   -   36
49   -   52

9   -   12

25   -   28
41   -   44

5   -   8

21   -   24
37   -   40
53   -   56

Address #2

LDM-32

1st LDM-E32

2nd LDM-E32

57   -   60
73   -   76
89   -   92

61   -   64
77   -   80
93   -   99

65   -   68
81   -   84

69   -   72
85   -   88

* System Status Indicators

View of LDM-32

not used
not used
not used

not used
Supervisory (Yellow LED)
Pre-Alarm
AC Fail (Yellow LED)

Panel Trouble

not used
not used

Signals Silenced (Yellow LED)

System Trouble (Yellow LED)

System Alarm (Red 

LED)

not 

It is assumed that this module/expander 
annunciates points 64-99.

Zones 90-99 are special function zones:

•

Z90 Presignal Time Run

•

Z91 Time Started/Release

•

Z92 Time Started/Release

•

Z93 Time Started/Release

•

Z94 Time Started/Release

•

Z95 Time Ctl Active

•

Z96Time Ctl Active

•

Z97 Holiday Active

•

Z98 Tornado

•

Z99 Pre-alarm

Figure E.3  Activation and Trouble Status Annunciation

Summary of Contents for NOTIFIER LDM Series





































































Reviews:

No comments