manualshive.com logo in svg

Honeywell NOTIFIER LDM Series, Instruction Manual, Page: 38 / 68

Share
Download
Honeywell NOTIFIER LDM Series Instruction Manual Download Page 38

38

LDM Series Instruction Manual —

 P/N 15885:H3 8/12/2019

System 5000 (UL 8th)

AIM-200 Point Annunciation

Figure B.6 illustrates the configuration of LDMs to annunciate alarms and troubles for up to 120 zones with the first eight points - 16 
LEDs (J5: P1 through P8 and J6: P1 through P8) dedicated to System 5000 system status annunciation. 

J6

J5

OUTPUTS

J7

J8

Alarm

Alarm

Alarm

Alarm

Trouble

Trouble

Trouble

Trouble

J6

J5

OUTPUTS

Address #1

LDM-32

1st LDM-E32

2nd LDM-E32

3rd LDM-E32

Address #2

LDM-32

1st LDM-E32

2nd LDM-E32

3rd LDM-E32

System Status Indicators*

9   -   12

25   -   28
41   -   44

13   -   16
29   -   32
45   -   48

1   -   4

17   -   20
33   -   36
49   -   52

5   -   8

21   -   24
37   -   40
53   -   56

57   -   60
73   -   76
89   -   92

105  -  108

65   -   68
81   -   84

97   -  100

113  -  116

69   -   72
85   -   88

101  -  104
117  -  120

61   -  64

77   -   80
93   -   96

109  -  112

view of LDM-32

* System Status Indicators

NAC Ckt #1 ON (Green LED)

NAC Ckt #2 ON (Green LED)
Municipal Tie ON (Red LED)
Alarm Relay ON (Red LED)

NAC Ckt #1 Trbl (Yellow LED)

NAC Ckt #2 Trbl (Yellow LED)

Municipal Tie Trbl (Yellow LED)
Alarm Relay Trbl (Yellow LED)

Supervisory (Yellow LED)

not used

Signals Silenced (Yellow LED)

System Trouble (Yellow LED)

System Alarm (Red LED)

not 

9   -   12

25   -   28
41   -   44

*It is assumed this module/expander annunciates points (circuits) 64-128.

Figure B.6  Alarm/Trouble Operation Without 8-Point Shift

Summary of Contents for NOTIFIER LDM Series





































































Reviews:

No comments