manualshive.com logo in svg

Honeywell NOTIFIER LDM Series, Instruction Manual, Page: 25 / 68

Share
Download
Honeywell NOTIFIER LDM Series Instruction Manual Download Page 25

LDM Series Instruction Manual —

 P/N 15885:H3 8/12/2019

25

Configuration for the LDM-32 and System 500

System 500 (UL 8th)

A.5  Configuration for the LDM-32 and System 500

LDM-32 DIP Switch (SW3) settings (for System 500):

1.

Relay Control:

 Future Use - this switch must be set OFF on the System 500.

None

One

2.

Number of LDM-E32 Expanders Installed:

OFF

ON

3.

Number of LDM-E32 Expanders Installed:

OFF

ON

4.

8-Point Shift

: Set switch ON to shift CPU-500 LED function annunciation out of the first eight annunciator positions on the

LDM-32. This switch is intended for systems between 9 and 16 circuits and employing one LDM-32 module (with no expander)
where annunciation of all circuits is desired.

5.

Receive Only: Set this switch ON for each LDM series that will provide the same information as another LDM series in a different
physical location (when two or more sets of LDM series have the same address, all but one must be configured as Receive Only.)

6.

Piezo Disable:

 Set this switch ON to disable the piezo from sounding for any event.

7.

Switch Inhibit: 

 To disable the point I/O control switches on the LDMs from functioning, set this switch ON. When inhibited, the

local Lamp Test switch continues to function. In addition, the Acknowledge/Lamp Test switch will function only in a local capacity,
unrecognized by the host System 500.

8.

Flash Inhibit:

 Set this switch ON to disable the flashing of LEDs associated with unacknowledged events. 

Flash Inhibit also

disables the piezo from sounding. Flash Inhibit must be ON when using the relay expander module (LDM-R32).

A.6  Annunciator Operation

Annunciator points 'track' or follow those System 500 points they are programmed to annunciate; they do not latch. Table A.1 outlines 
the annunciation of various System 500 circuits and functions. Note: Control Switches marked 'not used' will still function as local 
LAMP TEST or local ACKNOWLEDGE switches for their respective points.

12

3

45

6

78

8

8

LDM-32

Switch set to 

ON

 position

Switch set to 

OFF

 position

Lamp Driver Address

Set in the range 01-04

Ones

Tens

DIP Switch SW3

(see settings below)

Lamp Driver Mode Switch

SW4

SW4

ALARM/TROUBLE

 mode

(SW4 set to right side)

ALARM ONLY

 mode

(SW4 set to left side)

Summary of Contents for NOTIFIER LDM Series





































































Reviews:

No comments