manualshive.com logo in svg

Honeywell NOTIFIER LDM Series, Instruction Manual, Page: 26 / 68

Share
Download
Honeywell NOTIFIER LDM Series Instruction Manual Download Page 26

26

LDM Series Instruction Manual —

 P/N 15885:H3 8/12/2019

System 500 (UL 8th)

Annunciator Operation

System 500 CPU Annunciator Point Assignments to LDMs

System 500 Option Modules Annunciator Point Assignments to LDMs

System 500 CPU Points

LDM Alarm Red LED

LDM Trouble/Supv Yellow LED

LDM Control Switches

Annunciator Point #1

a

1 

If the 8-Point Shift (DIP switch #4 of SW3) is set ON, the eight functions (ACK, SIL, RESET, LAMP TEST, NAC1, NAC2, MUNTIE, 

RELAY) will be shifted out of annunciator points 1 through 8. These eight points would then annunciate the status of the first eight zones.

Indicates System Alarm

Indicates System Trouble

Functions as an 

ACKNOWLEDGE

Annunciator Point #2

not used

Indicates that signals have been 

silenced

Functions as a SIGNAL 

SILENCE

Annunciator Point #3

not used

not used

Functions as a SYSTEM 

RESET

Annunciator Point #4

not used

Indicates Supervisory Condition

not used

Annunciator Point #5

Indicates that Notification Circuit 1 

has been activated

Indicates trouble status of circuit

Controls Notification Circuit 1

Annunciator Point #6

Indicates that Notification Circuit 2 

has been activated

Indicates trouble status of circuit

Controls Notification Circuit 2

Annunciator Point #7

Indicates that the Remote Signaling 

Municipal Tie has been activated

Indicates trouble status of circuit

Controls Remote Signaling 

Municipal Tie

Annunciator Point #8

Indicates that the Alarm Relay has 

been activated

Indicates Module Trouble, Power 

Failure, or Disabled Circuit(s)

Controls Alarm Relay

System 500 CPU Points

LDM Alarm LED Red

LDM Trouble/Supv LED Yellow

LDM Control Switches

a

1 

Optional control switches are active only if all of these conditions are met:

a) Receive Only (DIP Switch #5) is set to OFF.
b) Switch Inhibit (DIP Switch #7) is set to OFF.

IZ-4, IZ-4A, IZ-8

Alarm Status per Circuit

b

2 

If an IZ-4, IZ-4A or IZ-8 circuit is programmed on the System 500 as a supervisory point, both the red and yellow LEDs will be 
illuminated for a supervisory condition. Illumination of the yellow LED alone indicates a trouble condition (open circuit) on the IZ 
supervisory circuit.

Trouble Status per Circuit

not used

IC-4, ICE-4, CR-4L

Indicates Activation

Indicates Trouble per Circuit

Control Notification Circuit

CR-4, CRE-4, CR-4L

Indicates Activation

Indicates Trouble per Circuit

Controls Relays

TC-2, TC-4

Indicates Activation

Indicates Trouble per Circuit

Remote Switch Functions

Alarm and Trouble Mode

 without 8-Point Shift

Alarm and Trouble Mode 

with 8-Point Shift

LDM Switch 

Position

LDM-32

1st LDM-E32

LDM Switch 

Position

LDM-32

1

ACK

Circuit  9

1

Circuit  1

2

SIG. SIL.

Circuit 10

2

Circuit 2

3

RESET

Circuit 11

3

Circuit 3

4

not used

Circuit 12

4

Circuit 4

5

NAC 1

Circuit 13

5

Circuit 5

6

NAC 2

Circuit 14

6

Circuit 6

7

MUN TIE

Circuit 15

7

Circuit 7

8

Alarm Relay

Circuit 16

8

Circuit 8

9

Circuit 1

Circuit 17

9

Circuit 9

10

Circuit 2

Circuit 18

10

Circuit 10

11

Circuit 3

Circuit 19

11

Circuit 11

12

Circuit 4

Circuit 20

12

Circuit 12

13

Circuit 5

Circuit 21

13

Circuit 13

14

Circuit 6

Circuit 22

14

Circuit 14

15

Circuit 7

Circuit 23

15

Circuit 15

16

Circuit 8

Circuit 24

16

Circuit 16

Table A.1  LDM Series Switch Control Functions

Summary of Contents for NOTIFIER LDM Series





































































Reviews:

No comments