manualshive.com logo in svg

Honeywell NOTIFIER LDM Series, Instruction Manual, Page: 12 / 68

Share
Download
Honeywell NOTIFIER LDM Series Instruction Manual Download Page 12

12

LDM Series Instruction Manual —

 P/N 15885:H3 8/12/2019

LDM Features

The LDM-R32

Keylock Control Switch Security

A UL listed key-lock switch wired to J4 on the LDM-32 should be used to provide access security 
for all control switches wired to that set of LDM modules. Control switches will not function 
when the key-lock switch is in its closed position.

2.8  The LDM-R32

The LDM-R32 Relay Expander Module provides the LDM-32 or LDM-E32 with 32 dry Form-A 
(normally open) contacts. The relay module serves as a slave to the particular lamp driver annun-
ciator it is connected to - instead of driving lamps or LEDs, the alarm and/or trouble signals from 
the LDM-32 and LDM-E32 modules are used to activate the relays on the LDM-R32. A maxi-
mum of two of these relay modules can be supported by an LDM-32/LDM-E32 operating in 
alarm-only mode, providing a maximum of 64 alarm relays. In alarm/trouble mode, one, two or 
four LDM-R32 modules may be connected to LDM-32/LDM-E32s, providing a maximum of 64 
alarm and 64 trouble relays. Includes mounting hardware, one Relay Power Cable and four Relay 
Expander Ribbon cables for connection to the master LDM-32/LDM-E32 module.

Keyswitch

LDM-32

2
1

J4

J5

J6

J7

J8

J10

K1

K2

K3

K4

K5

K6

K7

K8

K9

K10

K11

K12

K13

K14

K15

K16

K17

K18

K19

K20

K21

K22

K23

K24

K25

K26

K27

K28

K29

K30

K31

TB1

TB5

TB2

TB3

TB6

TB4

K32

1

1

8

1

1

1

2

2

7

2

2

2

3

3

6

3

3

3

4

4

5

4

4

4

5

5

4

5

6

6

3

6

7

7

2

7

8

8

1

8

Figure 2.3  LDM-R32

Summary of Contents for NOTIFIER LDM Series





































































Reviews:

No comments