Honeywell NOTIFIER LDM Series Instruction Manual Download Page 33 | Manualshive

Page: 33 / 68

Honeywell NOTIFIER LDM Series Instruction Manual Download Page 33

LDM Series Instruction Manual —

P/N 15885:H3 8/12/2019

33

Configuration for the LDM-32 and System 5000

System 5000 (UL 8th)

B.5 Configuration for the LDM-32 and System 5000

LDM-32 DIP Switch (SW3) settings (for System 5000):

1.

Relay Control:

Future Use - this switch must be set OFF on the System 5000.

None

One

Two

Four

2.

Number of LDM-E32 Expanders Installed

:

OFF

ON

OFF

ON

3.

Number of LDM-E32 Expanders Installed:

OFF

OFF

ON

ON

4.

8-Point Shift

: Set switch ON to shift CPU-5000 LED function annunciation from the first eight annunciator positions on the

LDM-32 to the third LDM-E32 expander positions 57 - 64. This shift can only be set on an LDM-32 set for address 1.

5.

Receive Only

: Set this switch ON for each LDM series that will provide the same information as another LDM series in a different

physical location (when two or more sets of LDM series have the same address, all but one must be configured as Receive Only.)

6.

Piezo Disable

: Set this switch ON to disable the piezo from sounding for any event.

7.

Switch Inhibit: T

o disable the point I/O control switches on the LDMs from functioning, set this switch ON. When inhibited, the

local Lamp Test switch continues to function. In addition, the Acknowledge/Lamp Test switch will function only in a local capacity,
unrecognized by the host System 5000.

8.

Flash Inhibit:

Set this switch ON to disable the flashing of LEDs associated with unacknowledged events. F

lash Inhibit also

disables the piezo from sounding. Flash Inhibit must be ON when using the relay expander module (LDM-R32).

*The lamp driver can be set for addresses 1, 2, 3 or 4. The actual mapping arrangement for a respective module and its expanders
depends on System 5000 annunciator programming. Refer to Document 15584 for details.

12

3

45

6

78

8

8

LDM-32

Switch set to

ON

position

Switch set to

OFF

position

Lamp Driver Address

Set in the range 01-04

Ones

Tens

DIP Switch SW3

(see settings below)

Lamp Driver Mode Switch

SW4

SW4

ALARM/TROUBLE

mode

(SW4 set to right side)

ALARM ONLY

mode

(SW4 set to left side)

«
...
31
32
33
34
35
...
»

Summary of Contents for NOTIFIER LDM Series





































































Reviews:

No comments