Honeywell KromSchroder IC 40 Technical Information Download Page 2

Page: 2 / 72

IC 40 · Edition 07.18

▼

= To be continued

Contents

Actuators IC 40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1 Examples of application . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.1.1 Staged control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

1.1.2 Staged control with three burner capacity levels . . . . .6

1.1.3 Continuous control by three-point step signal. . . . . . . . 7

1.1.4 Staged control with pre-purge . . . . . . . . . . . . . . . . . . . . . . . .8

1.1.5 Continuous control with defined ignition position . . . .9

1.1.6 Hot-air compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.1.7 Staged control with online adjustment of the

burner capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2 Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

3.1 Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3.2 Standard and analogue operating modes . . . . . . . .13
3.3 Closed, low-fire rate, intermediate and open

position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

3.4 Running times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.5 Standard operating modes 1 – 12 . . . . . . . . . . . . . . . .15

3.5.1 2-point operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.5.2 2-point operation with flame proving period . . . . . . . 16

3.5.3 2-stage operation with one or two digital inputs . . . .17

3.5.4 2-stage operation with two digital inputs. . . . . . . . . . . 19

3.5.5 3-point step operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.5.6 3-stage operation with one or two digital inputs . . . .21

3.5.7 2-point operation with switchover of the

adjustment angle for the “open” position . . . . . . . . . . . . . . . . . 23

3.5.8 2-point operation with input-dependent

adjustment angle for the “open” position . . . . . . . . . . . . . . . . . 25

3.5.9 2-point operation with switchover of the running

times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3.5.10 3-point step operation with running time

fractions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

3.5.11 3-stage operation with two digital inputs . . . . . . . . . 29

3.5.12 3-point step operation with low position . . . . . . . . . . 30

3.6 Analogue operating modes 21 – 27 . . . . . . . . . . . . . . 31

3.6.1 2-point operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

3.6.2 2-point operation with switchover of the

adjustment angle for the “open” position . . . . . . . . . . . . . . . . . 33

3.6.3 2-point operation with input-dependent

adjustment angle for the “open” position . . . . . . . . . . . . . . . . . 35

3.6.4 2-point operation with switchover of the running

times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

3.6.5 2-point operation with characteristic curve

switchover I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

3.6.6 2-point operation with characteristic curve

switchover II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

3.6.7 2-stage operation with two digital inputs and

variable adjustment angle for the “open” position . . . . . . . . 42

3.6.8 Emergency closing function . . . . . . . . . . . . . . . . . . . . . . . . 43

3.7 Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

3.7.1 Parameter sets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

3.7.2 Factory default parameters. . . . . . . . . . . . . . . . . . . . . . . . . . .47

3.8 Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

3.8.1 Digital. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

3.8.2 Analogue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

3.9 Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
3.10 Manual mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

3.10.1 Direct position preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

3.10.2 Simulate inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

3.11 Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

3.11.1 Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

3.11.2 Measured values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

3.11.3 Resetting statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

3.11.4 Resetting a signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

3.12 Connection diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
3.13 Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

3.13.1 During operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

3.13.2 Warnings and faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

3.14 Relay outputs RO 1 and RO 2 function. . . . . . . . . .56

Summary of Contents for KromSchroder IC 40









































































Search results

Summary of Contents for KromSchroder IC 40

Reviews:

Honeywell KromSchroder IC 40, Technical Information, Page: 2 / 72

Search results

Summary of Contents for KromSchroder IC 40

Reviews: